Tuesday, December 03 2013 intratical_12F calibration #12F+off: intermediate set for Oct2013 after #12 new intermediate T0 set for October 2013 after 12. Used T0s from 12+off (OID 107995666) and runes of 13/10/2013. /nLog available at: "http://ific.uv.es/~agusanlo/calibrations/intratical_12F" /////////////////////////////////////////////////////////////////////////////////////////////////////////// Intraline calibration performed with standard LED-OB calibration runes of 13/10/2013: online calibration "2013:V1.0" with rigid alignment: > LABEL = "2013:V1.0" ( VERSION_ID = 107995777 ) (<- Interline offsets included) > ARS_T0_VERSION = 107995666 > ARS_TVC_VERSION = 57889518 > ARS_AVC_0PE_VERSION = 95788267 > ARS_AVC_1PE_VERSION = 107973065 > ALIGNMENT_VERSION = 59100183 > ARS_XT_VERSION = 64970555 walk correction disabled (old style), no more corrections (cross talk, etc) in consideration taken (old style) Section #0 1-3 (Not performed) Section #1 4-10 Section #2 11-16(17) Section #3 17-22(23) Section #4 23-25 Also these LED OBs were not available: L10S21 L11S02 L11S09 L11S15 L11S21 L12S02 L12S15 OBs under investigation in order to try to recover them. Added T0s for IL13 ars available in "select * from antares.ars_geography where line=14;" using clockphases as default T0s: line floor lcm_id clk/t0 ars 14 0 1595 1075.089 6,7,8 14 4 1235 2280.994 0,1,8 14 5 1597 2726.844 0,1,8 Clockphases: > old runTimeStamp = 1355117600 (Mon, 10 Dec 2012 05:33:20 +0000 (GMT) + 0 nsec) > old CLOCK_RUN_ID = 167021 > old CLOCK_CONFIGURATION_ID = 276 > new runTimeStamp = 1382313600 (Mon, 21 Oct 2013 00:00:00 +0000 (GMT) + 0 nsec) > new CLOCK_RUN_ID = 169534 > new CLOCK_CONFIGURATION_ID = 277 > WARNING: The compared Clock-Phases have not the same CLOCK_CONFIGURATION_ID. > Histogram Statistics T0s: > Minimum difference: -15.4434 > Maximum difference: 18.0549 > Histogram Statistics CLKs: > Minimum difference: -0.053 > Maximum difference: 0.048 > Histogram Statistics T0s+CLKs: > Minimum difference: -15.4664 > Maximum difference: 18.0559 new T0 ID 122403184 /////////////////////////////////////////////////////////////////////////////////////////////////////////// Observations during revision of the autobinning-intratical output: In general a worsening w.r.t older calibrations has been appreciated. Besides the LED OBs recovery investigation, still remains to solve the weak points of the calibration, aka that is independant between sectors, dependant of the fitted slope (section #1 of line 4) and section #4 cases with very few OMs. /////////////////////////////////////////////////////////////////////////////////////////////////////////// Calibration_manager Statistics after the human inspection: > Statistics: (1770 ARS) - 354 with no run (i.e. no OB) available to perform calibration. [0ns APPLIED] (LED OBs not used: L10S21 L11S02 L11S09 L11S15 L11S21 L12S02 L12S15 ) - 285 which their histograms don't exist. [0ns APPLIED] - 4 are an official Dead Channel not among the listed before. [0ns APPLIED] - 1040 are ready to be corrected without problems. - 32 are a pair of ARSs miscalibrated more than 1ns. [32 REVISED (100%) / 0 TOUCHÉ REMAINS] - 18 have a bad performed fit but lie in the fit zone. [18 APPLIED (100%)] - 51 lie out of the exclusion zone with a good fit performed. [51 APPLIED (100%)] - 18 lie out of the exclusion zone with a bad fit performed. [18 APPLIED (100%)] All counted sum a total of 1770 ARSs. - 0 should still be revised + 0 perfect ARS pairs. At The End: - 643 couldn't be corrected. (no data or dead channel) - 11 were decided not to be corrected. (0ns of correction) - 1116 were decided to be corrected: · 1007 less than 1ns. · 55 between 1ns and 2ns. · 30 between 2ns and 5ns. · 24 more than 5ns. - And 32 are in a pair corrected more than 1ns: · 28 less than 2ns. · 2 between 2ns and 5ns. · 2 more than 5ns. /////////////////////////////////////////////////////////////////////////////////////////////////////////// > TOP 100 BIGGEST CORRECTIONS: 1) L09 S06 ars1 ( 9061 ): -18.0549 ns 2) L09 S06 ars0 ( 9060 ): -16.8055 ns 3) L09 S18 ars5 ( 9185 ): +15.4434 ns 4) L09 S18 ars4 ( 9184 ): +14.9359 ns 5) L06 S13 ars2 ( 6132 ): -13.397 ns 6) L06 S13 ars3 ( 6133 ): -12.3535 ns 7) L02 S09 ars1 ( 2091 ): -11.2755 ns 8) L06 S10 ars4 ( 6104 ): -10.9836 ns 9) L06 S10 ars5 ( 6105 ): -10.8876 ns 10) L10 S17 ars3 ( 10173 ): -10.8085 ns 11) L10 S17 ars2 ( 10172 ): -10.7933 ns 12) L09 S14 ars1 ( 9141 ): -10.3908 ns 13) L09 S14 ars0 ( 9140 ): -9.55507 ns 14) L03 S20 ars4 ( 3204 ): -8.54805 ns 15) L03 S20 ars5 ( 3205 ): -7.94239 ns 16) L03 S12 ars5 ( 3125 ): -7.58496 ns 17) L02 S09 ars0 ( 2090 ): -7.24529 ns 18) L06 S12 ars2 ( 6122 ): -6.81327 ns 19) L06 S12 ars3 ( 6123 ): -6.78407 ns 20) L08 S10 ars4 ( 8104 ): -6.41162 ns 21) L03 S13 ars3 ( 3133 ): -6.01631 ns 22) L02 S09 ars5 ( 2095 ): -5.64325 ns 23) L03 S13 ars2 ( 3132 ): -5.49265 ns 24) L02 S09 ars4 ( 2094 ): -5.36817 ns 25) L08 S10 ars5 ( 8105 ): -4.73149 ns 26) L07 S05 ars2 ( 7052 ): -4.17048 ns 27) L07 S05 ars3 ( 7053 ): -4.14123 ns 28) L03 S21 ars5 ( 3215 ): -4.09058 ns 29) L04 S25 ars0 ( 4250 ): -4.02952 ns 30) L04 S07 ars1 ( 4071 ): +3.61575 ns 31) L09 S15 ars3 ( 9153 ): -3.57792 ns 32) L03 S07 ars1 ( 3071 ): -3.40762 ns 33) L09 S15 ars2 ( 9152 ): -3.39671 ns 34) L01 S19 ars1 ( 1191 ): -3.35094 ns 35) L03 S09 ars5 ( 3095 ): -3.22521 ns 36) L03 S21 ars4 ( 3214 ): -3.00122 ns 37) L04 S07 ars0 ( 4070 ): +2.96089 ns 38) L10 S09 ars5 ( 10095 ): -2.8424 ns 39) L03 S09 ars4 ( 3094 ): -2.83758 ns 40) L03 S07 ars0 ( 3070 ): -2.72326 ns 41) L01 S05 ars0 ( 1050 ): -2.71918 ns 42) L09 S13 ars2 ( 9132 ): -2.67535 ns 43) L04 S25 ars1 ( 4251 ): -2.60199 ns 44) L09 S19 ars0 ( 9190 ): -2.598 ns 45) L09 S13 ars3 ( 9133 ): -2.58769 ns 46) L06 S05 ars5 ( 6055 ): -2.58237 ns 47) L08 S25 ars2 ( 8252 ): -2.46279 ns 48) L04 S18 ars1 ( 4181 ): -2.34308 ns 49) L04 S18 ars0 ( 4180 ): -2.27667 ns 50) L03 S12 ars4 ( 3124 ): -2.23495 ns 51) L09 S19 ars1 ( 9191 ): -2.23033 ns 52) L01 S22 ars5 ( 1225 ): -2.1304 ns 53) L09 S09 ars0 ( 9090 ): -2.1282 ns 54) L02 S20 ars4 ( 2204 ): -2.01094 ns 55) L06 S05 ars4 ( 6054 ): -1.99235 ns 56) L01 S16 ars0 ( 1160 ): -1.83154 ns 57) L04 S10 ars3 ( 4103 ): -1.80692 ns 58) L08 S25 ars3 ( 8253 ): -1.79459 ns 59) L09 S22 ars3 ( 9223 ): -1.78293 ns 60) L02 S20 ars5 ( 2205 ): -1.77895 ns 61) L06 S05 ars2 ( 6052 ): -1.75715 ns 62) L08 S20 ars3 ( 8203 ): -1.70603 ns 63) L01 S10 ars3 ( 1103 ): -1.70452 ns 64) L04 S07 ars4 ( 4074 ): -1.67468 ns 65) L09 S16 ars1 ( 9161 ): -1.65871 ns 66) L09 S22 ars2 ( 9222 ): -1.6474 ns 67) L09 S10 ars5 ( 9105 ): -1.59652 ns 68) L04 S15 ars0 ( 4150 ): +1.57035 ns 69) L10 S09 ars4 ( 10094 ): -1.56779 ns 70) L01 S16 ars1 ( 1161 ): -1.54114 ns 71) L09 S16 ars0 ( 9160 ): -1.52673 ns 72) L05 S12 ars4 ( 5124 ): +1.50058 ns 73) L05 S12 ars5 ( 5125 ): +1.47674 ns 74) L01 S05 ars1 ( 1051 ): -1.43176 ns 75) L09 S09 ars1 ( 9091 ): -1.4255 ns 76) L12 S12 ars2 ( 12122 ): -1.40684 ns 77) L08 S16 ars1 ( 8161 ): +1.40606 ns 78) L01 S19 ars0 ( 1190 ): -1.38585 ns 79) L07 S09 ars1 ( 7091 ): -1.3698 ns 80) L06 S09 ars3 ( 6093 ): +1.36368 ns 81) L08 S15 ars3 ( 8153 ): +1.32523 ns 82) L06 S20 ars0 ( 6200 ): -1.28711 ns 83) L03 S21 ars0 ( 3210 ): +1.28171 ns 84) L12 S12 ars3 ( 12123 ): -1.2733 ns 85) L09 S07 ars2 ( 9072 ): -1.2669 ns 86) L08 S20 ars2 ( 8202 ): -1.26499 ns 87) L06 S20 ars1 ( 6201 ): -1.25978 ns 88) L08 S15 ars2 ( 8152 ): +1.25618 ns 89) L06 S04 ars2 ( 6042 ): +1.22512 ns 90) L09 S07 ars3 ( 9073 ): -1.22209 ns 91) L06 S09 ars4 ( 6094 ): -1.22167 ns 92) L09 S06 ars3 ( 9063 ): -1.18239 ns 93) L06 S18 ars3 ( 6183 ): -1.17945 ns 94) L06 S18 ars2 ( 6182 ): -1.1645 ns 95) L08 S16 ars0 ( 8160 ): +1.15799 ns 96) L06 S04 ars3 ( 6043 ): +1.12117 ns 97) L07 S09 ars0 ( 7090 ): -1.10895 ns 98) L03 S21 ars1 ( 3211 ): +1.10862 ns 99) L02 S16 ars4 ( 2164 ): +1.09788 ns 100) L06 S07 ars0 ( 6070 ): -1.08356 ns /////////////////////////////////////////////////////////////////////////////////////////////////////////// ARS that couldn't be corrected (no data or Dead Channel): L01 S01 ars0; L01 S01 ars1; L01 S01 ars2; L01 S01 ars3; L01 S01 ars4; L01 S01 ars5; L01 S02 ars0; L01 S02 ars1; L01 S02 ars2; L01 S02 ars3; L01 S02 ars4; L01 S02 ars5; L01 S03 ars0; L01 S03 ars1; L01 S03 ars2; L01 S03 ars3; L01 S03 ars4; L01 S03 ars5; L01 S04 ars0; L01 S04 ars1; ; ; ; ; ; ; L01 S05 ars2; L01 S05 ars3; ; ; L01 S06 ars0; L01 S06 ars1; ; ; ; ; L01 S07 ars0; L01 S07 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L01 S10 ars0; L01 S10 ars1; ; ; ; ; ; ; L01 S11 ars2; L01 S11 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L01 S14 ars0; L01 S14 ars1; ; ; ; ; ; ; L01 S15 ars2; L01 S15 ars3; ; ; ; ; ; ; L01 S16 ars4; L01 S16 ars5; ; ; ; ; ; ; ; ; L01 S18 ars2; L01 S18 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L01 S22 ars2; L01 S22 ars3; ; ; ; ; ; ; ; ; ; ; ; ; L01 S24 ars4; L01 S24 ars5; ; ; ; ; ; ; L02 S01 ars0; L02 S01 ars1; L02 S01 ars2; L02 S01 ars3; L02 S01 ars4; L02 S01 ars5; L02 S02 ars0; L02 S02 ars1; L02 S02 ars2; L02 S02 ars3; L02 S02 ars4; L02 S02 ars5; L02 S03 ars0; L02 S03 ars1; L02 S03 ars2; L02 S03 ars3; L02 S03 ars4; L02 S03 ars5; L02 S04 ars0; L02 S04 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L02 S07 ars0; L02 S07 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L02 S10 ars0; L02 S10 ars1; L02 S10 ars2; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L02 S16 ars0; L02 S16 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L02 S19 ars4; L02 S19 ars5; ; ; ; ; ; ; ; ; ; ; ; ; L02 S22 ars0; L02 S22 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L03 S01 ars0; L03 S01 ars1; L03 S01 ars2; L03 S01 ars3; L03 S01 ars4; L03 S01 ars5; L03 S02 ars0; L03 S02 ars1; L03 S02 ars2; L03 S02 ars3; L03 S02 ars4; L03 S02 ars5; L03 S03 ars0; L03 S03 ars1; L03 S03 ars2; L03 S03 ars3; L03 S03 ars4; L03 S03 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L03 S08 ars0; L03 S08 ars1; L03 S08 ars2; L03 S08 ars3; L03 S08 ars4; L03 S08 ars5; ; ; L03 S09 ars2; L03 S09 ars3; ; ; ; ; ; ; ; ; L03 S11 ars0; L03 S11 ars1; ; ; ; ; ; ; L03 S12 ars2; L03 S12 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L03 S15 ars2; L03 S15 ars3; ; ; ; ; ; ; ; ; ; ; L03 S17 ars2; L03 S17 ars3; ; ; ; ; ; ; L03 S18 ars4; L03 S18 ars5; ; ; ; ; L03 S19 ars4; L03 S19 ars5; ; ; ; ; ; ; ; ; L03 S21 ars2; L03 S21 ars3; ; ; ; ; ; ; L03 S22 ars4; L03 S22 ars5; ; ; ; ; ; ; ; ; ; ; ; ; L03 S25 ars0; L03 S25 ars1; ; ; ; ; L04 S01 ars0; L04 S01 ars1; L04 S01 ars2; L04 S01 ars3; L04 S01 ars4; L04 S01 ars5; L04 S02 ars0; L04 S02 ars1; L04 S02 ars2; L04 S02 ars3; L04 S02 ars4; L04 S02 ars5; L04 S03 ars0; L04 S03 ars1; L04 S03 ars2; L04 S03 ars3; L04 S03 ars4; L04 S03 ars5; ; ; L04 S04 ars2; L04 S04 ars3; ; ; ; ; ; ; L04 S05 ars4; L04 S05 ars5; ; ; L04 S06 ars2; L04 S06 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L04 S12 ars0; L04 S12 ars1; ; ; ; ; ; ; ; ; ; ; ; ; L04 S14 ars2; L04 S14 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L04 S17 ars4; L04 S17 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L04 S21 ars2; L04 S21 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L05 S01 ars0; L05 S01 ars1; L05 S01 ars2; L05 S01 ars3; L05 S01 ars4; L05 S01 ars5; L05 S02 ars0; L05 S02 ars1; L05 S02 ars2; L05 S02 ars3; L05 S02 ars4; L05 S02 ars5; L05 S03 ars0; L05 S03 ars1; L05 S03 ars2; L05 S03 ars3; L05 S03 ars4; L05 S03 ars5; ; ; ; ; L05 S04 ars4; L05 S04 ars5; ; ; ; ; L05 S05 ars4; L05 S05 ars5; ; ; ; ; ; ; L05 S07 ars0; L05 S07 ars1; ; ; ; ; ; ; L05 S08 ars2; L05 S08 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L05 S11 ars4; L05 S11 ars5; L05 S12 ars0; L05 S12 ars1; ; ; ; ; ; ; L05 S13 ars2; L05 S13 ars3; ; ; ; ; L05 S14 ars2; L05 S14 ars3; ; ; ; ; ; ; ; ; L05 S16 ars0; L05 S16 ars1; L05 S16 ars2; L05 S16 ars3; L05 S16 ars4; L05 S16 ars5; ; ; ; ; ; ; ; ; ; ; L05 S18 ars4; L05 S18 ars5; L05 S19 ars0; L05 S19 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L05 S22 ars4; L05 S22 ars5; ; ; ; ; ; ; L05 S24 ars0; L05 S24 ars1; L05 S24 ars2; L05 S24 ars3; ; ; L05 S25 ars0; L05 S25 ars1; ; ; L05 S25 ars4; L05 S25 ars5; L06 S01 ars0; L06 S01 ars1; L06 S01 ars2; L06 S01 ars3; L06 S01 ars4; L06 S01 ars5; L06 S02 ars0; L06 S02 ars1; L06 S02 ars2; L06 S02 ars3; L06 S02 ars4; L06 S02 ars5; L06 S03 ars0; L06 S03 ars1; L06 S03 ars2; L06 S03 ars3; L06 S03 ars4; L06 S03 ars5; ; ; ; ; L06 S04 ars4; L06 S04 ars5; L06 S05 ars0; L06 S05 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L06 S15 ars4; L06 S15 ars5; ; ; L06 S16 ars2; L06 S16 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L06 S20 ars4; L06 S20 ars5; ; ; ; ; ; ; ; ; L06 S22 ars2; L06 S22 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L06 S25 ars4; L06 S25 ars5; L07 S01 ars0; L07 S01 ars1; L07 S01 ars2; L07 S01 ars3; L07 S01 ars4; L07 S01 ars5; L07 S02 ars0; L07 S02 ars1; L07 S02 ars2; L07 S02 ars3; L07 S02 ars4; L07 S02 ars5; L07 S03 ars0; L07 S03 ars1; L07 S03 ars2; L07 S03 ars3; L07 S03 ars4; L07 S03 ars5; ; ; L07 S04 ars2; L07 S04 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L07 S11 ars0; L07 S11 ars1; ; ; L07 S11 ars4; L07 S11 ars5; ; ; ; ; L07 S12 ars4; L07 S12 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L07 S16 ars0; L07 S16 ars1; L07 S16 ars2; L07 S16 ars3; ; ; L07 S17 ars0; L07 S17 ars1; ; ; ; ; ; ; ; ; ; ; ; ; L07 S19 ars2; L07 S19 ars3; ; ; L07 S20 ars0; L07 S20 ars1; L07 S20 ars2; L07 S20 ars3; ; ; ; ; ; ; L07 S21 ars4; L07 S21 ars5; L07 S22 ars0; L07 S22 ars1; ; ; ; ; ; ; L07 S23 ars2; L07 S23 ars3; L07 S23 ars4; L07 S23 ars5; ; ; ; ; ; ; ; ; L07 S25 ars2; L07 S25 ars3; ; ; L08 S01 ars0; L08 S01 ars1; L08 S01 ars2; L08 S01 ars3; L08 S01 ars4; L08 S01 ars5; L08 S02 ars0; L08 S02 ars1; L08 S02 ars2; L08 S02 ars3; L08 S02 ars4; L08 S02 ars5; L08 S03 ars0; L08 S03 ars1; L08 S03 ars2; L08 S03 ars3; L08 S03 ars4; L08 S03 ars5; ; ; ; ; ; ; ; ; ; ; ; ; L08 S06 ars0; L08 S06 ars1; ; ; ; ; ; ; ; ; L08 S07 ars4; L08 S07 ars5; ; ; ; ; ; ; ; ; ; ; L08 S09 ars4; L08 S09 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L08 S15 ars0; L08 S15 ars1; ; ; ; ; ; ; ; ; ; ; L08 S17 ars0; L08 S17 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L08 S20 ars4; L08 S20 ars5; ; ; L08 S21 ars2; L08 S21 ars3; ; ; L08 S22 ars0; L08 S22 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L09 S01 ars0; L09 S01 ars1; L09 S01 ars2; L09 S01 ars3; L09 S01 ars4; L09 S01 ars5; L09 S02 ars0; L09 S02 ars1; L09 S02 ars2; L09 S02 ars3; L09 S02 ars4; L09 S02 ars5; L09 S03 ars0; L09 S03 ars1; L09 S03 ars2; L09 S03 ars3; L09 S03 ars4; L09 S03 ars5; ; ; ; ; ; ; L09 S05 ars0; L09 S05 ars1; ; ; L09 S05 ars4; L09 S05 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L09 S11 ars4; L09 S11 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L09 S18 ars2; L09 S18 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L09 S22 ars4; L09 S22 ars5; L09 S23 ars0; L09 S23 ars1; L09 S23 ars2; L09 S23 ars3; L09 S23 ars4; L09 S23 ars5; ; ; ; ; ; ; ; ; ; ; ; ; L10 S01 ars0; L10 S01 ars1; L10 S01 ars2; L10 S01 ars3; L10 S01 ars4; L10 S01 ars5; L10 S02 ars0; L10 S02 ars1; L10 S02 ars2; L10 S02 ars3; L10 S02 ars4; L10 S02 ars5; L10 S03 ars0; L10 S03 ars1; L10 S03 ars2; L10 S03 ars3; L10 S03 ars4; L10 S03 ars5; ; ; ; ; ; ; ; ; L10 S05 ars2; L10 S05 ars3; ; ; ; ; L10 S06 ars2; L10 S06 ars3; ; ; ; ; L10 S07 ars2; L10 S07 ars3; L10 S07 ars4; L10 S07 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L10 S12 ars2; L10 S12 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L10 S16 ars2; L10 S16 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L10 S19 ars4; L10 S19 ars5; ; ; L10 S20 ars2; L10 S20 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L10 S23 ars0; L10 S23 ars1; L10 S23 ars2; L10 S23 ars3; L10 S23 ars4; L10 S23 ars5; L10 S24 ars0; L10 S24 ars1; L10 S24 ars2; L10 S24 ars3; L10 S24 ars4; L10 S24 ars5; L10 S25 ars0; L10 S25 ars1; L10 S25 ars2; L10 S25 ars3; L10 S25 ars4; L10 S25 ars5; L11 S01 ars0; L11 S01 ars1; L11 S01 ars2; L11 S01 ars3; L11 S01 ars4; L11 S01 ars5; L11 S02 ars0; L11 S02 ars1; L11 S02 ars2; L11 S02 ars3; L11 S02 ars4; L11 S02 ars5; L11 S03 ars0; L11 S03 ars1; L11 S03 ars2; L11 S03 ars3; L11 S03 ars4; L11 S03 ars5; L11 S04 ars0; L11 S04 ars1; L11 S04 ars2; L11 S04 ars3; L11 S04 ars4; L11 S04 ars5; L11 S05 ars0; L11 S05 ars1; L11 S05 ars2; L11 S05 ars3; L11 S05 ars4; L11 S05 ars5; L11 S06 ars0; L11 S06 ars1; L11 S06 ars2; L11 S06 ars3; L11 S06 ars4; L11 S06 ars5; L11 S07 ars0; L11 S07 ars1; L11 S07 ars2; L11 S07 ars3; L11 S07 ars4; L11 S07 ars5; L11 S08 ars0; L11 S08 ars1; L11 S08 ars2; L11 S08 ars3; L11 S08 ars4; L11 S08 ars5; L11 S09 ars0; L11 S09 ars1; L11 S09 ars2; L11 S09 ars3; L11 S09 ars4; L11 S09 ars5; L11 S10 ars0; L11 S10 ars1; L11 S10 ars2; L11 S10 ars3; L11 S10 ars4; L11 S10 ars5; L11 S11 ars0; L11 S11 ars1; L11 S11 ars2; L11 S11 ars3; L11 S11 ars4; L11 S11 ars5; L11 S12 ars0; L11 S12 ars1; L11 S12 ars2; L11 S12 ars3; L11 S12 ars4; L11 S12 ars5; L11 S13 ars0; L11 S13 ars1; L11 S13 ars2; L11 S13 ars3; L11 S13 ars4; L11 S13 ars5; L11 S14 ars0; L11 S14 ars1; L11 S14 ars2; L11 S14 ars3; L11 S14 ars4; L11 S14 ars5; L11 S15 ars0; L11 S15 ars1; L11 S15 ars2; L11 S15 ars3; L11 S15 ars4; L11 S15 ars5; L11 S16 ars0; L11 S16 ars1; L11 S16 ars2; L11 S16 ars3; L11 S16 ars4; L11 S16 ars5; L11 S17 ars0; L11 S17 ars1; L11 S17 ars2; L11 S17 ars3; L11 S17 ars4; L11 S17 ars5; L11 S18 ars0; L11 S18 ars1; L11 S18 ars2; L11 S18 ars3; L11 S18 ars4; L11 S18 ars5; L11 S19 ars0; L11 S19 ars1; L11 S19 ars2; L11 S19 ars3; L11 S19 ars4; L11 S19 ars5; L11 S20 ars0; L11 S20 ars1; L11 S20 ars2; L11 S20 ars3; L11 S20 ars4; L11 S20 ars5; L11 S21 ars0; L11 S21 ars1; L11 S21 ars2; L11 S21 ars3; L11 S21 ars4; L11 S21 ars5; L11 S22 ars0; L11 S22 ars1; L11 S22 ars2; L11 S22 ars3; L11 S22 ars4; L11 S22 ars5; L11 S23 ars0; L11 S23 ars1; L11 S23 ars2; L11 S23 ars3; L11 S23 ars4; L11 S23 ars5; L11 S24 ars0; L11 S24 ars1; L11 S24 ars2; L11 S24 ars3; L11 S24 ars4; L11 S24 ars5; L11 S25 ars0; L11 S25 ars1; L11 S25 ars2; L11 S25 ars3; L11 S25 ars4; L11 S25 ars5; L12 S01 ars0; L12 S01 ars1; L12 S01 ars2; L12 S01 ars3; L12 S01 ars4; L12 S01 ars5; L12 S02 ars0; L12 S02 ars1; L12 S02 ars2; L12 S02 ars3; L12 S02 ars4; L12 S02 ars5; L12 S03 ars0; L12 S03 ars1; L12 S03 ars2; L12 S03 ars3; L12 S03 ars4; L12 S03 ars5; L12 S04 ars0; L12 S04 ars1; L12 S04 ars2; L12 S04 ars3; L12 S04 ars4; L12 S04 ars5; L12 S05 ars0; L12 S05 ars1; L12 S05 ars2; L12 S05 ars3; L12 S05 ars4; L12 S05 ars5; L12 S06 ars0; L12 S06 ars1; L12 S06 ars2; L12 S06 ars3; L12 S06 ars4; L12 S06 ars5; L12 S07 ars0; L12 S07 ars1; L12 S07 ars2; L12 S07 ars3; L12 S07 ars4; L12 S07 ars5; L12 S08 ars0; L12 S08 ars1; L12 S08 ars2; L12 S08 ars3; L12 S08 ars4; L12 S08 ars5; L12 S09 ars0; L12 S09 ars1; L12 S09 ars2; L12 S09 ars3; L12 S09 ars4; L12 S09 ars5; L12 S10 ars0; L12 S10 ars1; L12 S10 ars2; L12 S10 ars3; L12 S10 ars4; L12 S10 ars5; ; ; ; ; L12 S11 ars4; L12 S11 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L12 S15 ars0; L12 S15 ars1; ; ; ; ; ; ; L12 S16 ars2; L12 S16 ars3; ; ; L12 S17 ars0; L12 S17 ars1; L12 S17 ars2; L12 S17 ars3; L12 S17 ars4; L12 S17 ars5; L12 S18 ars0; L12 S18 ars1; L12 S18 ars2; L12 S18 ars3; L12 S18 ars4; L12 S18 ars5; L12 S19 ars0; L12 S19 ars1; L12 S19 ars2; L12 S19 ars3; L12 S19 ars4; L12 S19 ars5; L12 S20 ars0; L12 S20 ars1; L12 S20 ars2; L12 S20 ars3; L12 S20 ars4; L12 S20 ars5; /////////////////////////////////////////////////////////////////////////////////////////////////////////// Execution of intratical program: evalu155:agusanlo/macros/tical> ./intratical -i /l/agusanlo/data/tical/intratical_12F/autobinning/ -o /l/agusanlo/data/tical/intratical_12F > Searching OB available... ID: 1628 (L01 S15) [ 1 run ] ID: 1631 (L01 S02) [ 1 run ] ID: 1621 (L01 S21) [ 1 run ] ID: 1643 (L01 S09) [ 1 run ] ID: 1065 (L02 S15) [ 1 run ] ID: 1095 (L02 S02) [ 1 run ] ID: 1118 (L02 S21) [ 1 run ] ID: 1048 (L02 S09) [ 1 run ] ID: 1140 (L03 S15) [ 1 run ] ID: 1027 (L03 S02) [ 1 run ] ID: 1106 (L03 S21) [ 1 run ] ID: 1157 (L03 S09) [ 1 run ] ID: 1115 (L04 S15) [ 1 run ] ID: 1091 (L04 S02) [ 1 run ] ID: 1151 (L04 S21) [ 1 run ] ID: 1141 (L04 S09) [ 1 run ] ID: 1163 (L05 S15) [ 1 run ] ID: 1193 (L05 S02) [ 1 run ] ID: 1158 (L05 S21) [ 1 run ] ID: 1159 (L05 S09) [ 1 run ] ID: 1046 (L06 S15) [ 1 run ] ID: 1092 (L06 S02) [ 1 run ] ID: 1056 (L06 S21) [ 1 run ] ID: 1186 (L06 S09) [ 1 run ] ID: 1042 (L07 S15) [ 1 run ] ID: 1195 (L07 S02) [ 1 run ] ID: 1177 (L07 S21) [ 1 run ] ID: 1116 (L07 S09) [ 1 run ] ID: 1138 (L08 S15) [ 1 run ] ID: 1232 (L08 S02) [ 1 run ] ID: 1219 (L08 S21) [ 1 run ] ID: 1176 (L08 S09) [ 1 run ] ID: 1068 (L09 S15) [ 1 run ] ID: 1025 (L09 S02) [ 1 run ] ID: 1263 (L09 S21) [ 1 run ] ID: 1247 (L09 S09) [ 1 run ] ID: 1249 (L10 S15) [ 1 run ] ID: 1242 (L10 S02) [ 1 run ] ID: 1277 (L10 S09) [ 1 run ] ID: 1038 (L12 S09) [ 1 run ] > Found 40 OBs! (in a total of 21 runes) >========================================================================================< >>> Calibrating Line 1: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1631 (L01 S02) > Fitting for time corrections... -> Fit: offset = -2.69 slope = 0.112 (parabola = 0.000184) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.314ns [*] · ars 3: -0.543ns [*] · ars 4: +0.197ns [*] · ars 5: +0.376ns [*] - Storey 5: · ars 0: -2.72ns [ ] · ars 1: -1.06ns [ ] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.363ns [*] · ars 5: +0.0608ns [*] - Storey 6: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.329ns [*] · ars 3: -0.264ns [*] · ars 4: -0.316ns [*] · ars 5: -0.339ns [*] - Storey 7: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.664ns [*] · ars 3: -0.476ns [*] · ars 4: +0.354ns [*] · ars 5: +0.339ns [*] - Storey 8: · ars 0: +0.475ns [*] · ars 1: -0.0275ns [*] · ars 2: +0.587ns [*] · ars 3: +0.501ns [*] · ars 4: +0.177ns [*] · ars 5: +0.296ns [*] - Storey 9: · ars 0: +0.301ns [*] · ars 1: +0.353ns [*] · ars 2: +0.337ns [*] · ars 3: +0.373ns [*] · ars 4: +0.419ns [*] · ars 5: +0.121ns [*] - Storey 10: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.961ns [*] · ars 3: -1.7ns [*] · ars 4: -0.00518ns [*] · ars 5: +0.313ns [*] > Section #2: Calibrating from St11 to St16 using OB 1643 (L01 S09) > Fitting for time corrections... -> Fit: offset = -0.262 slope = 0.102 (parabola = -4.17e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: +0.239ns [*] · ars 1: +0.455ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.591ns [*] · ars 5: -0.527ns [*] - Storey 12: · ars 0: +0.131ns [*] · ars 1: +0.14ns [*] · ars 2: -0.126ns [*] · ars 3: -0.241ns [*] · ars 4: +0.0423ns [*] · ars 5: +0.237ns [ ] - Storey 13: · ars 0: +0.437ns [*] · ars 1: +0.458ns [*] · ars 2: +0.148ns [*] · ars 3: -0.0452ns [*] · ars 4: +0.411ns [*] · ars 5: +0.255ns [*] - Storey 14: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.495ns [*] · ars 3: +0.731ns [*] · ars 4: -0.896ns [*] · ars 5: -1.06ns [*] - Storey 15: · ars 0: -0.00659ns [*] · ars 1: +0.378ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.342ns [*] · ars 5: +0.116ns [*] - Storey 16: · ars 0: -1.83ns [*] · ars 1: -1.54ns [*] · ars 2: -0.168ns [*] · ars 3: +0.235ns [*] · ars 4: Not Available · ars 5: Not Available > Section #3: Calibrating from St17 to St22 using OB 1628 (L01 S15) > Fitting for time corrections... -> Fit: offset = 1.02 slope = 0.089 (parabola = 2.09e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.131ns [*] · ars 1: -0.0667ns [*] · ars 2: -0.269ns [*] · ars 3: -0.278ns [*] · ars 4: -0.194ns [*] · ars 5: -0.0153ns [*] - Storey 18: · ars 0: +0.0609ns [*] · ars 1: +0.046ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.152ns [*] · ars 5: +0.11ns [*] - Storey 19: · ars 0: -47.4ns [ ] · ars 1: -3.35ns [ ] · ars 2: +0.189ns [*] · ars 3: +0.139ns [*] · ars 4: -0.122ns [*] · ars 5: +0.446ns [*] - Storey 20: · ars 0: +0.347ns [*] · ars 1: +0.408ns [*] · ars 2: -0.181ns [*] · ars 3: +0.364ns [*] · ars 4: +0.64ns [*] · ars 5: +0.795ns [*] - Storey 21: · ars 0: -0.266ns [*] · ars 1: -0.412ns [*] · ars 2: -0.187ns [*] · ars 3: -0.112ns [*] · ars 4: -0.793ns [*] · ars 5: -0.603ns [*] - Storey 22: · ars 0: -0.189ns [*] · ars 1: -0.453ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.515ns [*] · ars 5: -2.13ns [ ] > Section #4: Calibrating from St23 to St25 using OB 1621 (L01 S21) > Fitting for time corrections... -> Fit: offset = 0.718 slope = 0.0869 (parabola = 0.00354) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: +0.245ns [*] · ars 1: +0.177ns [*] · ars 2: -0.249ns [*] · ars 3: -0.49ns [*] · ars 4: -0.313ns [*] · ars 5: -0.49ns [*] - Storey 24: · ars 0: +0.499ns [*] · ars 1: +0.335ns [*] · ars 2: +0.694ns [*] · ars 3: +0.712ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 25: · ars 0: +0.151ns [*] · ars 1: -0.137ns [*] · ars 2: -0.389ns [*] · ars 3: -0.287ns [*] · ars 4: -0.21ns [*] · ars 5: -0.248ns [*] >========================================================================================< >>> Calibrating Line 2: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1095 (L02 S02) > Fitting for time corrections... -> Fit: offset = -1.14 slope = 0.0529 (parabola = 0.000188) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.333ns [*] · ars 3: -0.129ns [*] · ars 4: -0.335ns [*] · ars 5: -0.31ns [*] - Storey 5: · ars 0: +0.166ns [*] · ars 1: +0.125ns [*] · ars 2: +0.0227ns [*] · ars 3: +0.344ns [*] · ars 4: -0.36ns [*] · ars 5: -0.349ns [*] - Storey 6: · ars 0: +0.44ns [*] · ars 1: +0.27ns [*] · ars 2: +0.567ns [*] · ars 3: +0.475ns [*] · ars 4: +0.105ns [*] · ars 5: +0.0346ns [*] - Storey 7: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.202ns [*] · ars 3: -0.0787ns [*] · ars 4: +0.0462ns [*] · ars 5: -0.0259ns [*] - Storey 8: · ars 0: +0.292ns [*] · ars 1: +0.461ns [*] · ars 2: +0.114ns [*] · ars 3: -0.217ns [*] · ars 4: -0.559ns [*] · ars 5: -0.458ns [*] - Storey 9: · ars 0: -4.15ns [ ] · ars 1: -4.89ns [ ] · ars 2: -0.0687ns [*] · ars 3: -0.291ns [*] · ars 4: -5.37ns [ ] · ars 5: -5.64ns [ ] - Storey 10: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: +91.2ns [ ] · ars 4: +0.0546ns [*] · ars 5: -0.204ns [*] > Section #2: Calibrating from St11 to St16 using OB 1048 (L02 S09) > Fitting for time corrections... -> Fit: offset = -0.161 slope = 0.0659 (parabola = 0.000274) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: +0.0183ns [*] · ars 1: -0.0271ns [*] · ars 2: -0.442ns [*] · ars 3: -0.501ns [*] · ars 4: -0.283ns [*] · ars 5: -0.407ns [*] - Storey 12: · ars 0: -0.139ns [*] · ars 1: -0.0306ns [*] · ars 2: -0.0266ns [*] · ars 3: -0.155ns [*] · ars 4: +0.201ns [*] · ars 5: +0.132ns [*] - Storey 13: · ars 0: +0.32ns [*] · ars 1: +0.507ns [*] · ars 2: -0.0963ns [*] · ars 3: +0.221ns [*] · ars 4: +0.361ns [*] · ars 5: +0.246ns [*] - Storey 14: · ars 0: -0.12ns [*] · ars 1: -0.0278ns [*] · ars 2: +0.0522ns [*] · ars 3: +0.0639ns [*] · ars 4: -0.0519ns [*] · ars 5: +0.393ns [*] - Storey 15: · ars 0: +0.0221ns [*] · ars 1: +0.354ns [*] · ars 2: +0.277ns [*] · ars 3: -0.156ns [*] · ars 4: +0.287ns [*] · ars 5: -0.0336ns [*] - Storey 16: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.334ns [*] · ars 3: -0.123ns [*] · ars 4: +1.1ns [*] · ars 5: +0.638ns [*] > Section #3: Calibrating from St17 to St22 using OB 1065 (L02 S15) > Fitting for time corrections... -> Fit: offset = -0.129 slope = 0.066 (parabola = -0.000179) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.455ns [*] · ars 1: +0.374ns [*] · ars 2: +0.464ns [*] · ars 3: -0.561ns [*] · ars 4: +0.122ns [*] · ars 5: +0.0517ns [*] - Storey 18: · ars 0: +0.0114ns [*] · ars 1: +0.241ns [*] · ars 2: +0.103ns [*] · ars 3: -0.0364ns [*] · ars 4: -0.0136ns [*] · ars 5: -0.239ns [*] - Storey 19: · ars 0: -0.136ns [*] · ars 1: -0.0877ns [*] · ars 2: -0.552ns [*] · ars 3: -0.293ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 20: · ars 0: +0.0113ns [*] · ars 1: -0.0777ns [*] · ars 2: +0.243ns [*] · ars 3: +0.58ns [*] · ars 4: -1.69ns [ ] · ars 5: -1.3ns [ ] - Storey 21: · ars 0: -0.603ns [*] · ars 1: -0.388ns [*] · ars 2: -0.267ns [*] · ars 3: -0.517ns [*] · ars 4: -0.00375ns [*] · ars 5: +0.153ns [*] - Storey 22: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.24ns [*] · ars 3: +0.0189ns [*] · ars 4: -0.235ns [*] · ars 5: -0.0477ns [*] > Section #4: Calibrating from St23 to St25 using OB 1118 (L02 S21) > Fitting for time corrections... -> Fit: offset = -8.12 slope = 0.188 (parabola = -0.00268) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: +0.129ns [*] · ars 1: -0.0379ns [*] · ars 2: +0.234ns [*] · ars 3: +0.291ns [*] · ars 4: +0.296ns [*] · ars 5: +0.209ns [*] - Storey 24: · ars 0: -0.207ns [*] · ars 1: -0.0528ns [*] · ars 2: -0.187ns [*] · ars 3: +0.0298ns [*] · ars 4: -0.997ns [*] · ars 5: -0.837ns [*] - Storey 25: · ars 0: +0.329ns [*] · ars 1: +0.453ns [*] · ars 2: +0.735ns [*] · ars 3: +0.416ns [*] · ars 4: -0.334ns [*] · ars 5: -0.47ns [*] >========================================================================================< >>> Calibrating Line 3: > Section #0: Calibrating from St01 to St03 using OB 1193 (L05 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1027 (L03 S02) > Fitting for time corrections... -> Fit: offset = -4.42 slope = 0.0823 (parabola = -2.54e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: +0.104ns [*] · ars 1: +0.148ns [*] · ars 2: -0.165ns [*] · ars 3: -0.164ns [*] · ars 4: -0.19ns [*] · ars 5: -0.188ns [ ] - Storey 5: · ars 0: +0.0662ns [*] · ars 1: -0.0813ns [*] · ars 2: +0.106ns [*] · ars 3: +0.117ns [*] · ars 4: +0.154ns [*] · ars 5: +0.0697ns [*] - Storey 6: · ars 0: +0.187ns [*] · ars 1: +0.381ns [*] · ars 2: -0.0191ns [*] · ars 3: -0.0298ns [*] · ars 4: +0.0209ns [*] · ars 5: +0.0367ns [*] - Storey 7: · ars 0: -2.72ns [ ] · ars 1: -3.41ns [ ] · ars 2: -0.111ns [*] · ars 3: -0.0664ns [*] · ars 4: -0.293ns [*] · ars 5: -0.462ns [*] - Storey 8: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available - Storey 9: · ars 0: -0.112ns [*] · ars 1: +0.0432ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -2.84ns [ ] · ars 5: -3.23ns [ ] - Storey 10: · ars 0: +0.0457ns [*] · ars 1: +0.244ns [*] · ars 2: +0.22ns [*] · ars 3: +0.169ns [*] · ars 4: -0.421ns [*] · ars 5: +0.00199ns [*] > Section #2: Calibrating from St11 to St16 using OB 1157 (L03 S09) > Fitting for time corrections... -> Fit: offset = -4.66 slope = 0.0697 (parabola = 2.89e-06) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.049ns [*] · ars 3: -0.0298ns [*] · ars 4: +0.0777ns [*] · ars 5: -0.0391ns [*] - Storey 12: · ars 0: +0.462ns [*] · ars 1: +0.45ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -52ns [ ] · ars 5: -7.58ns [ ] - Storey 13: · ars 0: -0.203ns [*] · ars 1: -0.216ns [*] · ars 2: -5.49ns [ ] · ars 3: -6.02ns [ ] · ars 4: -0.83ns [*] · ars 5: -0.823ns [*] - Storey 14: · ars 0: +0.18ns [*] · ars 1: +0.225ns [*] · ars 2: -94.7ns [ ] · ars 3: -94.3ns [ ] · ars 4: +0.0377ns [*] · ars 5: -0.105ns [*] - Storey 15: · ars 0: +0.0293ns [*] · ars 1: +0.439ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.35ns [*] · ars 5: +0.512ns [*] - Storey 16: · ars 0: +0.415ns [*] · ars 1: -0.00974ns [*] · ars 2: -0.419ns [*] · ars 3: -0.743ns [*] · ars 4: +0.304ns [*] · ars 5: +0.161ns [*] > Section #3: Calibrating from St17 to St22 using OB 1140 (L03 S15) > Fitting for time corrections... -> Fit: offset = -5.02 slope = 0.0669 (parabola = 0.000454) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: -0.223ns [*] · ars 1: -0.0532ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.111ns [*] · ars 5: +0.21ns [*] - Storey 18: · ars 0: -0.679ns [*] · ars 1: -0.782ns [*] · ars 2: -0.658ns [*] · ars 3: -0.626ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 19: · ars 0: +0.54ns [*] · ars 1: +0.195ns [*] · ars 2: +0.033ns [*] · ars 3: +0.0438ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 20: · ars 0: +0.274ns [*] · ars 1: +0.494ns [*] · ars 2: +0.598ns [*] · ars 3: +0.669ns [*] · ars 4: -8.55ns [ ] · ars 5: -7.94ns [ ] - Storey 21: · ars 0: +1.28ns [*] · ars 1: +1.11ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -3ns [ ] · ars 5: -4.09ns [ ] - Storey 22: · ars 0: +0.253ns [*] · ars 1: +0.433ns [*] · ars 2: +0.0923ns [*] · ars 3: -0.122ns [*] · ars 4: Not Available · ars 5: Not Available > Section #4: Calibrating from St23 to St25 using OB 1106 (L03 S21) > Fitting for time corrections... -> Fit: offset = -8.8 slope = 0.171 (parabola = -0.00038) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: -0.646ns [*] · ars 1: -0.569ns [*] · ars 2: +0.409ns [*] · ars 3: +0.372ns [*] · ars 4: +0.365ns [*] · ars 5: +0.201ns [*] - Storey 24: · ars 0: +0.00344ns [*] · ars 1: -0.312ns [*] · ars 2: +0.596ns [*] · ars 3: +0.382ns [ ] · ars 4: -0.244ns [*] · ars 5: -0.307ns [*] - Storey 25: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.338ns [*] · ars 3: +0.271ns [*] · ars 4: -0.417ns [*] · ars 5: -0.0596ns [*] >========================================================================================< >>> Calibrating Line 4: > Section #0: Calibrating from St01 to St03 using OB 1092 (L06 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1091 (L04 S02) > Fitting for time corrections... -> Fit: offset = 1.07 slope = 0.0124 (parabola = 8.57e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: +0.00217ns [*] · ars 1: +0.0888ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.892ns [ ] · ars 5: -0.59ns [*] - Storey 5: · ars 0: +0.192ns [*] · ars 1: +0.37ns [*] · ars 2: +0.128ns [*] · ars 3: +0.132ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 6: · ars 0: +0.199ns [*] · ars 1: +0.0488ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.672ns [*] · ars 5: -0.0861ns [*] - Storey 7: · ars 0: +2.96ns [ ] · ars 1: +3.62ns [ ] · ars 2: +0.806ns [*] · ars 3: +1.04ns [*] · ars 4: -1.67ns [*] · ars 5: -0.895ns [*] - Storey 8: · ars 0: -0.481ns [*] · ars 1: +0.605ns [ ] · ars 2: +0.597ns [*] · ars 3: +0.781ns [*] · ars 4: +0.0912ns [*] · ars 5: +0.307ns [*] - Storey 9: · ars 0: +0.132ns [*] · ars 1: +0.285ns [*] · ars 2: -0.107ns [*] · ars 3: -0.124ns [*] · ars 4: +0.102ns [*] · ars 5: +0.233ns [*] - Storey 10: · ars 0: +0.0675ns [*] · ars 1: +0.247ns [*] · ars 2: -0.822ns [*] · ars 3: -1.81ns [*] · ars 4: +0.74ns [*] · ars 5: +0.674ns [*] > Section #2: Calibrating from St11 to St16 using OB 1141 (L04 S09) > Fitting for time corrections... -> Fit: offset = -3.16 slope = 0.1 (parabola = 0.000327) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: +0.423ns [*] · ars 1: -43.5ns [ ] · ars 2: -0.37ns [*] · ars 3: -0.151ns [*] · ars 4: -0.402ns [*] · ars 5: -0.204ns [*] - Storey 12: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.166ns [*] · ars 3: -0.288ns [*] · ars 4: +0.133ns [*] · ars 5: -0.0629ns [*] - Storey 13: · ars 0: -0.654ns [*] · ars 1: -0.776ns [*] · ars 2: +0.393ns [*] · ars 3: +0.441ns [*] · ars 4: +0.0902ns [*] · ars 5: +0.365ns [*] - Storey 14: · ars 0: -0.16ns [*] · ars 1: -0.196ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.377ns [*] · ars 5: +0.416ns [*] - Storey 15: · ars 0: +1.57ns [*] · ars 1: +0.551ns [*] · ars 2: -0.498ns [*] · ars 3: -0.395ns [*] · ars 4: +0.0722ns [*] · ars 5: +0.205ns [*] - Storey 16: · ars 0: +0.725ns [*] · ars 1: +0.443ns [*] · ars 2: +0.275ns [*] · ars 3: +0.719ns [*] · ars 4: +0.254ns [*] · ars 5: -0.0202ns [*] > Section #3: Calibrating from St17 to St22 using OB 1115 (L04 S15) > Fitting for time corrections... -> Fit: offset = -3.19 slope = 0.0774 (parabola = 0.000368) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: -0.193ns [*] · ars 1: -0.4ns [*] · ars 2: -0.627ns [*] · ars 3: -0.627ns [*] · ars 4: -2.85ns [ ] · ars 5: -1.38ns [ ] - Storey 18: · ars 0: -2.28ns [ ] · ars 1: -2.34ns [ ] · ars 2: +0.0156ns [*] · ars 3: +0.0247ns [*] · ars 4: -0.196ns [*] · ars 5: -0.00109ns [*] - Storey 19: · ars 0: +0.325ns [*] · ars 1: +0.585ns [*] · ars 2: +0.261ns [*] · ars 3: +0.416ns [*] · ars 4: +0.671ns [*] · ars 5: +0.462ns [*] - Storey 20: · ars 0: +0.291ns [*] · ars 1: +0.704ns [*] · ars 2: +0.184ns [*] · ars 3: +0.0173ns [*] · ars 4: -0.23ns [*] · ars 5: -0.182ns [*] - Storey 21: · ars 0: -0.0736ns [*] · ars 1: +0.149ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.766ns [*] · ars 5: -0.781ns [*] - Storey 22: · ars 0: +0.637ns [*] · ars 1: +0.296ns [*] · ars 2: +0.661ns [*] · ars 3: -0.146ns [*] · ars 4: -0.0736ns [*] · ars 5: +0.202ns [*] > Section #4: Calibrating from St23 to St25 using OB 1151 (L04 S21) > Fitting for time corrections... -> Fit: offset = -3.32 slope = 0.107 (parabola = 0.00184) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: -0.0272ns [*] · ars 1: +0.17ns [*] · ars 2: -0.0155ns [*] · ars 3: -0.186ns [*] · ars 4: -0.0528ns [*] · ars 5: -0.607ns [*] - Storey 24: · ars 0: +0.402ns [*] · ars 1: +0.748ns [*] · ars 2: +0.0206ns [*] · ars 3: -0.113ns [*] · ars 4: +0.229ns [*] · ars 5: +0.149ns [*] - Storey 25: · ars 0: -4.03ns [ ] · ars 1: -49.7ns [ ] · ars 2: -0.144ns [*] · ars 3: +0.0595ns [*] · ars 4: -0.118ns [*] · ars 5: -0.515ns [*] >========================================================================================< >>> Calibrating Line 5: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1193 (L05 S02) > Fitting for time corrections... -> Fit: offset = -6.65 slope = 0.073 (parabola = -0.000206) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: -0.23ns [*] · ars 1: +0.0198ns [*] · ars 2: +0.519ns [*] · ars 3: +0.331ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 5: · ars 0: -0.0927ns [*] · ars 1: -0.0513ns [*] · ars 2: +0.0109ns [*] · ars 3: +0.145ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 6: · ars 0: +0.0826ns [*] · ars 1: -0.0868ns [*] · ars 2: +0.172ns [*] · ars 3: +0.0772ns [*] · ars 4: +0.086ns [*] · ars 5: -0.0132ns [*] - Storey 7: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.272ns [*] · ars 3: -0.161ns [*] · ars 4: -0.261ns [*] · ars 5: -0.397ns [*] - Storey 8: · ars 0: -0.109ns [*] · ars 1: +0.078ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.0241ns [*] · ars 5: +0.257ns [*] - Storey 9: · ars 0: -0.629ns [*] · ars 1: -0.461ns [*] · ars 2: -0.23ns [*] · ars 3: +0.241ns [*] · ars 4: -0.751ns [*] · ars 5: -0.565ns [*] - Storey 10: · ars 0: +0.431ns [*] · ars 1: +0.761ns [*] · ars 2: -0.025ns [*] · ars 3: +0.302ns [*] · ars 4: +0.132ns [*] · ars 5: +0.665ns [*] > Section #2: Calibrating from St11 to St16 using OB 1159 (L05 S09) > Fitting for time corrections... -> Fit: offset = -10 slope = 0.109 (parabola = 0.000166) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: -0.474ns [*] · ars 1: -0.577ns [*] · ars 2: -0.256ns [*] · ars 3: -0.297ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 12: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.59ns [*] · ars 3: -0.716ns [*] · ars 4: +1.5ns [*] · ars 5: +1.48ns [*] - Storey 13: · ars 0: +0.109ns [*] · ars 1: -0.127ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.128ns [*] · ars 5: -0.219ns [*] - Storey 14: · ars 0: +0.191ns [*] · ars 1: -0.0512ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.204ns [*] · ars 5: +0.456ns [*] - Storey 15: · ars 0: -0.259ns [*] · ars 1: -0.152ns [*] · ars 2: +0.29ns [*] · ars 3: +0.388ns [*] · ars 4: -0.131ns [*] · ars 5: +0.0237ns [*] - Storey 16: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available > Section #3: Calibrating from St17 to St22 using OB 1163 (L05 S15) > Fitting for time corrections... -> Fit: offset = -3.64 slope = 0.0456 (parabola = -5.88e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: -0.0134ns [*] · ars 1: -0.0109ns [*] · ars 2: +0.161ns [*] · ars 3: +0.47ns [*] · ars 4: +0.0821ns [*] · ars 5: +0.335ns [*] - Storey 18: · ars 0: +0.276ns [*] · ars 1: +0.282ns [*] · ars 2: -0.938ns [*] · ars 3: -47.2ns [ ] · ars 4: Not Available · ars 5: Not Available - Storey 19: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.67ns [*] · ars 3: -0.569ns [*] · ars 4: -0.266ns [*] · ars 5: -0.164ns [*] - Storey 20: · ars 0: -0.00249ns [*] · ars 1: +0.0453ns [*] · ars 2: -0.603ns [*] · ars 3: -0.226ns [*] · ars 4: +0.448ns [*] · ars 5: +0.607ns [*] - Storey 21: · ars 0: +0.452ns [*] · ars 1: +0.379ns [*] · ars 2: -0.28ns [*] · ars 3: -0.0314ns [*] · ars 4: -73.4ns [ ] · ars 5: -95.1ns [ ] - Storey 22: · ars 0: +0.391ns [*] · ars 1: -0.231ns [*] · ars 2: +0.348ns [*] · ars 3: +0.0793ns [*] · ars 4: Not Available · ars 5: Not Available > Section #4: Calibrating from St23 to St25 using OB 1158 (L05 S21) > Fitting for time corrections... -> Fit: offset = -28.4 slope = 0.857 (parabola = 0.0383) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: -0.366ns [*] · ars 1: -0.607ns [*] · ars 2: +0.53ns [*] · ars 3: +0.312ns [*] · ars 4: +0.0493ns [*] · ars 5: +0.0813ns [*] - Storey 24: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: +8.08ns [ ] · ars 5: +8.15ns [ ] - Storey 25: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.705ns [*] · ars 3: -0.705ns [*] · ars 4: Not Available · ars 5: Not Available >========================================================================================< >>> Calibrating Line 6: > Section #0: Calibrating from St01 to St03 using OB 1091 (L04 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1092 (L06 S02) > Fitting for time corrections... -> Fit: offset = -2.65 slope = 0.0883 (parabola = -5.28e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: -0.0723ns [*] · ars 1: +0.0334ns [*] · ars 2: +1.23ns [*] · ars 3: +1.12ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 5: · ars 0: Not Available · ars 1: Not Available · ars 2: -1.76ns [*] · ars 3: -0.997ns [*] · ars 4: -1.99ns [*] · ars 5: -2.58ns [ ] - Storey 6: · ars 0: +0.378ns [*] · ars 1: +0.603ns [*] · ars 2: +0.833ns [*] · ars 3: +0.833ns [*] · ars 4: -0.476ns [*] · ars 5: -0.345ns [*] - Storey 7: · ars 0: -1.08ns [*] · ars 1: -0.696ns [*] · ars 2: +0.836ns [*] · ars 3: +0.98ns [*] · ars 4: +0.636ns [*] · ars 5: +0.686ns [*] - Storey 8: · ars 0: -0.137ns [*] · ars 1: -0.106ns [*] · ars 2: -0.262ns [*] · ars 3: -0.389ns [*] · ars 4: +0.432ns [*] · ars 5: +0.474ns [*] - Storey 9: · ars 0: -1.02ns [*] · ars 1: -0.5ns [*] · ars 2: +0.726ns [*] · ars 3: +1.36ns [*] · ars 4: -1.22ns [*] · ars 5: -0.867ns [*] - Storey 10: · ars 0: -0.229ns [*] · ars 1: -0.167ns [*] · ars 2: +0.675ns [*] · ars 3: +0.478ns [*] · ars 4: -11ns [ ] · ars 5: -10.9ns [ ] > Section #2: Calibrating from St11 to St16 using OB 1186 (L06 S09) > Fitting for time corrections... -> Fit: offset = -4.87 slope = 0.0875 (parabola = -3.32e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: +0.365ns [*] · ars 1: +0.392ns [*] · ars 2: +0.339ns [*] · ars 3: +0.311ns [*] · ars 4: -0.158ns [*] · ars 5: -0.041ns [*] - Storey 12: · ars 0: -0.0586ns [*] · ars 1: -0.00949ns [*] · ars 2: -6.81ns [ ] · ars 3: -6.78ns [ ] · ars 4: -0.552ns [*] · ars 5: -0.483ns [*] - Storey 13: · ars 0: -0.282ns [*] · ars 1: +0.101ns [*] · ars 2: -13.4ns [ ] · ars 3: -12.4ns [ ] · ars 4: -0.737ns [*] · ars 5: -0.462ns [*] - Storey 14: · ars 0: -0.582ns [*] · ars 1: -0.449ns [*] · ars 2: +0.324ns [*] · ars 3: +0.24ns [*] · ars 4: +0.42ns [*] · ars 5: +0.451ns [*] - Storey 15: · ars 0: +0.621ns [*] · ars 1: +0.324ns [*] · ars 2: +0.402ns [*] · ars 3: +0.259ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 16: · ars 0: -0.0279ns [*] · ars 1: -0.105ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.517ns [*] · ars 5: +0.0138ns [*] > Section #3: Calibrating from St17 to St22 using OB 1046 (L06 S15) > Fitting for time corrections... -> Fit: offset = 2.24 slope = 0.0679 (parabola = 6.28e-06) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.248ns [*] · ars 1: +0.342ns [*] · ars 2: -0.0049ns [ ] · ars 3: -0.039ns [*] · ars 4: -0.362ns [*] · ars 5: -0.242ns [*] - Storey 18: · ars 0: +0.217ns [*] · ars 1: +0.324ns [*] · ars 2: -43.8ns [ ] · ars 3: -1.18ns [*] · ars 4: +0.186ns [*] · ars 5: +0.089ns [*] - Storey 19: · ars 0: +0.573ns [*] · ars 1: +0.701ns [*] · ars 2: -0.548ns [*] · ars 3: -0.148ns [*] · ars 4: +0.108ns [*] · ars 5: +0.349ns [*] - Storey 20: · ars 0: -1.29ns [*] · ars 1: -1.26ns [*] · ars 2: +0.907ns [*] · ars 3: +0.968ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 21: · ars 0: +0.499ns [*] · ars 1: +0.398ns [*] · ars 2: -0.429ns [*] · ars 3: -0.357ns [*] · ars 4: -0.371ns [*] · ars 5: +0.209ns [*] - Storey 22: · ars 0: +0.412ns [*] · ars 1: +0.334ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.465ns [*] · ars 5: -0.173ns [*] > Section #4: Calibrating from St23 to St25 using OB 1056 (L06 S21) > Fitting for time corrections... -> Fit: offset = -7.3 slope = 0.186 (parabola = 0.00265) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: -0.649ns [*] · ars 1: -1.07ns [*] · ars 2: +0.514ns [*] · ars 3: +0.203ns [*] · ars 4: -0.0238ns [*] · ars 5: -0.000469ns [*] - Storey 24: · ars 0: +0.551ns [*] · ars 1: +0.605ns [*] · ars 2: -0.0762ns [*] · ars 3: -0.0113ns [*] · ars 4: +0.497ns [*] · ars 5: +0.493ns [*] - Storey 25: · ars 0: -0.706ns [*] · ars 1: -0.708ns [*] · ars 2: +0.165ns [*] · ars 3: +0.22ns [*] · ars 4: Not Available · ars 5: Not Available >========================================================================================< >>> Calibrating Line 7: > Section #0: Calibrating from St01 to St03 using OB 1025 (L09 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1195 (L07 S02) > Fitting for time corrections... -> Fit: offset = -5.81 slope = 0.0878 (parabola = 4.29e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: -0.375ns [*] · ars 1: +0.0745ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.439ns [ ] · ars 5: -0.306ns [*] - Storey 5: · ars 0: -0.372ns [*] · ars 1: +0.0408ns [*] · ars 2: -4.17ns [ ] · ars 3: -4.14ns [ ] · ars 4: +0.0194ns [*] · ars 5: +0.0941ns [*] - Storey 6: · ars 0: +0.0787ns [*] · ars 1: +0.244ns [*] · ars 2: +0.223ns [*] · ars 3: +0.571ns [*] · ars 4: +0.341ns [*] · ars 5: +0.417ns [*] - Storey 7: · ars 0: -0.287ns [*] · ars 1: -0.578ns [*] · ars 2: +0.373ns [*] · ars 3: +0.0652ns [*] · ars 4: +0.113ns [*] · ars 5: -0.323ns [*] - Storey 8: · ars 0: +0.349ns [*] · ars 1: +0.192ns [*] · ars 2: -0.257ns [*] · ars 3: -0.175ns [*] · ars 4: +0.069ns [*] · ars 5: -0.0597ns [*] - Storey 9: · ars 0: -1.11ns [*] · ars 1: -1.37ns [*] · ars 2: -0.154ns [*] · ars 3: +0.032ns [*] · ars 4: +0.569ns [*] · ars 5: +0.936ns [*] - Storey 10: · ars 0: -0.319ns [*] · ars 1: -0.433ns [*] · ars 2: +0.604ns [*] · ars 3: +0.763ns [*] · ars 4: -0.208ns [*] · ars 5: +0.158ns [*] > Section #2: Calibrating from St11 to St16 using OB 1116 (L07 S09) > Fitting for time corrections... -> Fit: offset = -2.85 slope = 0.0585 (parabola = -1.29e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.00233ns [*] · ars 3: -0.0934ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 12: · ars 0: +0.11ns [*] · ars 1: +0.205ns [*] · ars 2: -0.0949ns [*] · ars 3: -0.209ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 13: · ars 0: -0.269ns [*] · ars 1: -0.202ns [*] · ars 2: +0.277ns [*] · ars 3: +0.17ns [*] · ars 4: -73.8ns [ ] · ars 5: -75.2ns [ ] - Storey 14: · ars 0: +0.124ns [*] · ars 1: +0.258ns [*] · ars 2: -0.182ns [*] · ars 3: -0.0953ns [*] · ars 4: +0.416ns [*] · ars 5: +0.312ns [*] - Storey 15: · ars 0: -0.432ns [*] · ars 1: -0.342ns [*] · ars 2: -0.301ns [*] · ars 3: -0.383ns [*] · ars 4: +0.402ns [*] · ars 5: +0.451ns [*] - Storey 16: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: -0.304ns [*] · ars 5: -0.363ns [*] > Section #3: Calibrating from St17 to St22 using OB 1042 (L07 S15) > Fitting for time corrections... -> Fit: offset = -3.88 slope = 0.0792 (parabola = 0.000268) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.316ns [*] · ars 3: -0.318ns [*] · ars 4: +0.416ns [*] · ars 5: +0.377ns [*] - Storey 18: · ars 0: +0.0769ns [*] · ars 1: -0.229ns [*] · ars 2: -0.548ns [*] · ars 3: -0.939ns [*] · ars 4: -0.451ns [*] · ars 5: -0.226ns [*] - Storey 19: · ars 0: +0.437ns [*] · ars 1: +0.615ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.673ns [*] · ars 5: +0.513ns [*] - Storey 20: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: -0.177ns [*] · ars 5: +0.161ns [*] - Storey 21: · ars 0: -0.333ns [*] · ars 1: -0.865ns [*] · ars 2: +0.869ns [*] · ars 3: +0.826ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 22: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.653ns [*] · ars 3: +0.341ns [*] · ars 4: -0.351ns [*] · ars 5: +0.0844ns [*] > Section #4: Calibrating from St23 to St25 using OB 1177 (L07 S21) > Fitting for time corrections... -> Fit: offset = -2.43 slope = 0.033 (parabola = 0.00019) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: +0.0572ns [*] · ars 1: -0.114ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available - Storey 24: · ars 0: -0.48ns [*] · ars 1: -0.114ns [*] · ars 2: -0.0132ns [*] · ars 3: +0.0229ns [*] · ars 4: +0.168ns [*] · ars 5: +0.53ns [*] - Storey 25: · ars 0: +0.21ns [*] · ars 1: +0.483ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.386ns [*] · ars 5: -0.365ns [*] >========================================================================================< >>> Calibrating Line 8: > Section #0: Calibrating from St01 to St03 using OB 1242 (L10 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1232 (L08 S02) > Fitting for time corrections... -> Fit: offset = 1 slope = 0.0614 (parabola = -9.32e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: -0.346ns [*] · ars 1: -0.192ns [*] · ars 2: +0.0195ns [ ] · ars 3: -0.123ns [*] · ars 4: +0.0135ns [*] · ars 5: -0.0119ns [ ] - Storey 5: · ars 0: +0.124ns [*] · ars 1: +0.00456ns [*] · ars 2: +0.391ns [*] · ars 3: +0.561ns [*] · ars 4: +0.0853ns [*] · ars 5: +0.247ns [*] - Storey 6: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.173ns [*] · ars 3: +0.3ns [*] · ars 4: -0.0897ns [*] · ars 5: +0.434ns [*] - Storey 7: · ars 0: -0.523ns [*] · ars 1: -0.552ns [*] · ars 2: +0.481ns [*] · ars 3: +0.0639ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 8: · ars 0: -0.907ns [*] · ars 1: -0.449ns [*] · ars 2: +0.154ns [*] · ars 3: +0.421ns [*] · ars 4: -0.601ns [*] · ars 5: -0.826ns [*] - Storey 9: · ars 0: +0.103ns [*] · ars 1: -0.0155ns [*] · ars 2: +0.271ns [*] · ars 3: +0.575ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 10: · ars 0: +0.011ns [*] · ars 1: +0.0263ns [*] · ars 2: +0.189ns [*] · ars 3: +0.341ns [*] · ars 4: -6.41ns [ ] · ars 5: -4.73ns [ ] > Section #2: Calibrating from St11 to St16 using OB 1176 (L08 S09) > Fitting for time corrections... -> Fit: offset = 0.337 slope = 0.0459 (parabola = 9.92e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: +0.326ns [*] · ars 1: +0.156ns [*] · ars 2: +0.314ns [*] · ars 3: +0.459ns [*] · ars 4: +0.441ns [*] · ars 5: +0.212ns [*] - Storey 12: · ars 0: -0.736ns [*] · ars 1: -0.991ns [*] · ars 2: -0.267ns [*] · ars 3: -0.405ns [*] · ars 4: -0.237ns [*] · ars 5: -0.312ns [*] - Storey 13: · ars 0: +0.36ns [*] · ars 1: +0.407ns [*] · ars 2: -0.486ns [*] · ars 3: -0.276ns [*] · ars 4: -0.188ns [*] · ars 5: -0.241ns [*] - Storey 14: · ars 0: +0.189ns [*] · ars 1: +0.135ns [*] · ars 2: -0.321ns [*] · ars 3: -0.051ns [*] · ars 4: -1.05ns [*] · ars 5: -0.53ns [*] - Storey 15: · ars 0: Not Available · ars 1: Not Available · ars 2: +1.26ns [*] · ars 3: +1.33ns [*] · ars 4: +0.755ns [*] · ars 5: +0.464ns [*] - Storey 16: · ars 0: +1.16ns [*] · ars 1: +1.41ns [*] · ars 2: +0.27ns [*] · ars 3: +0.0167ns [*] · ars 4: -0.32ns [*] · ars 5: -0.251ns [*] > Section #3: Calibrating from St17 to St22 using OB 1138 (L08 S15) > Fitting for time corrections... -> Fit: offset = -1.49 slope = 0.0792 (parabola = -0.000141) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.333ns [*] · ars 3: +0.0743ns [*] · ars 4: +0.588ns [*] · ars 5: +0.452ns [*] - Storey 18: · ars 0: -0.869ns [*] · ars 1: -0.628ns [*] · ars 2: -0.964ns [*] · ars 3: -0.866ns [*] · ars 4: +0.167ns [*] · ars 5: +0.0597ns [*] - Storey 19: · ars 0: +0.5ns [*] · ars 1: +0.39ns [*] · ars 2: +0.718ns [*] · ars 3: +0.733ns [*] · ars 4: +0.988ns [*] · ars 5: +0.775ns [*] - Storey 20: · ars 0: -0.157ns [*] · ars 1: -0.342ns [*] · ars 2: -1.26ns [*] · ars 3: -1.71ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 21: · ars 0: +0.383ns [*] · ars 1: +0.165ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.389ns [*] · ars 5: -0.0157ns [*] - Storey 22: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.236ns [*] · ars 3: +0.432ns [*] · ars 4: -0.746ns [*] · ars 5: -0.487ns [*] > Section #4: Calibrating from St23 to St25 using OB 1219 (L08 S21) > Fitting for time corrections... -> Fit: offset = -4.45 slope = 0.188 (parabola = -0.000859) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: -0.0341ns [*] · ars 1: -0.273ns [*] · ars 2: +0.147ns [*] · ars 3: -0.0864ns [*] · ars 4: +0.44ns [*] · ars 5: +0.157ns [*] - Storey 24: · ars 0: +0.142ns [*] · ars 1: -0.0792ns [*] · ars 2: -0.233ns [*] · ars 3: -0.708ns [*] · ars 4: +0.398ns [*] · ars 5: -0.22ns [*] - Storey 25: · ars 0: +0.671ns [*] · ars 1: +0.762ns [*] · ars 2: -2.46ns [ ] · ars 3: -1.79ns [*] · ars 4: +0.166ns [*] · ars 5: +0.546ns [*] >========================================================================================< >>> Calibrating Line 9: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1025 (L09 S02) > Fitting for time corrections... -> Fit: offset = 3.74 slope = 0.056 (parabola = -0.000203) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: +0.0495ns [*] · ars 1: +0.00169ns [*] · ars 2: -0.0705ns [*] · ars 3: -0.0126ns [ ] · ars 4: +0.291ns [*] · ars 5: +0.339ns [*] - Storey 5: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.201ns [*] · ars 3: +0.0524ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 6: · ars 0: -16.8ns [ ] · ars 1: -18.1ns [ ] · ars 2: -0.236ns [*] · ars 3: -1.18ns [ ] · ars 4: +0.214ns [*] · ars 5: +0.221ns [*] - Storey 7: · ars 0: +0.0728ns [*] · ars 1: +0.133ns [*] · ars 2: -1.27ns [*] · ars 3: -1.22ns [*] · ars 4: +0.588ns [*] · ars 5: +0.463ns [*] - Storey 8: · ars 0: -0.191ns [*] · ars 1: -0.0216ns [*] · ars 2: -0.388ns [*] · ars 3: -0.404ns [*] · ars 4: -0.106ns [*] · ars 5: +0.38ns [*] - Storey 9: · ars 0: -2.13ns [ ] · ars 1: -1.43ns [*] · ars 2: +0.27ns [*] · ars 3: +0.135ns [*] · ars 4: +0.292ns [*] · ars 5: +0.159ns [*] - Storey 10: · ars 0: +0.346ns [*] · ars 1: +0.454ns [*] · ars 2: +0.433ns [*] · ars 3: +0.238ns [*] · ars 4: -0.592ns [ ] · ars 5: -1.6ns [ ] > Section #2: Calibrating from St11 to St16 using OB 1247 (L09 S09) > Fitting for time corrections... -> Fit: offset = -2.28 slope = 0.0681 (parabola = -0.000166) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: -0.21ns [*] · ars 1: +0.0746ns [*] · ars 2: -0.0287ns [*] · ars 3: -0.084ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 12: · ars 0: +0.065ns [*] · ars 1: +0.081ns [*] · ars 2: -0.0946ns [*] · ars 3: -0.359ns [*] · ars 4: +0.78ns [*] · ars 5: +1.06ns [*] - Storey 13: · ars 0: -0.574ns [*] · ars 1: -0.415ns [*] · ars 2: -2.68ns [ ] · ars 3: -2.59ns [ ] · ars 4: -0.0778ns [*] · ars 5: +0.0695ns [*] - Storey 14: · ars 0: -9.56ns [ ] · ars 1: -10.4ns [ ] · ars 2: -0.00134ns [*] · ars 3: +0.204ns [*] · ars 4: -33ns [ ] · ars 5: -34.6ns [ ] - Storey 15: · ars 0: -0.0681ns [*] · ars 1: -0.18ns [*] · ars 2: -3.4ns [ ] · ars 3: -3.58ns [ ] · ars 4: +0.00754ns [*] · ars 5: -0.0258ns [*] - Storey 16: · ars 0: -1.53ns [*] · ars 1: -1.66ns [*] · ars 2: +0.0193ns [*] · ars 3: -0.263ns [*] · ars 4: +0.399ns [*] · ars 5: +0.783ns [*] > Section #3: Calibrating from St17 to St22 using OB 1068 (L09 S15) > Fitting for time corrections... -> Fit: offset = -4.27 slope = 0.0638 (parabola = 0.000127) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: -0.412ns [*] · ars 1: -0.391ns [*] · ars 2: +0.669ns [*] · ars 3: +0.202ns [*] · ars 4: +0.092ns [ ] · ars 5: +0.095ns [*] - Storey 18: · ars 0: -0.164ns [*] · ars 1: -0.422ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +14.9ns [ ] · ars 5: +15.4ns [ ] - Storey 19: · ars 0: -2.6ns [ ] · ars 1: -2.23ns [ ] · ars 2: +0.0522ns [*] · ars 3: +0.3ns [*] · ars 4: -0.0259ns [*] · ars 5: -0.177ns [*] - Storey 20: · ars 0: +0.423ns [*] · ars 1: +0.289ns [*] · ars 2: +0.00391ns [*] · ars 3: +0.0268ns [*] · ars 4: -0.597ns [*] · ars 5: -1.02ns [*] - Storey 21: · ars 0: +0.685ns [*] · ars 1: +0.551ns [*] · ars 2: +0.422ns [*] · ars 3: +0.501ns [*] · ars 4: +0.465ns [*] · ars 5: +0.194ns [*] - Storey 22: · ars 0: +0.96ns [*] · ars 1: +0.795ns [*] · ars 2: -1.65ns [*] · ars 3: -1.78ns [*] · ars 4: Not Available · ars 5: Not Available > Section #4: Calibrating from St23 to St25 using OB 1263 (L09 S21) > Fitting for time corrections... -> Fit: offset = 72.5 slope = 0.0818 (parabola = -0.00412) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available - Storey 24: · ars 0: -0.344ns [*] · ars 1: -0.252ns [*] · ars 2: +0.129ns [*] · ars 3: +0.0608ns [*] · ars 4: +0.026ns [*] · ars 5: +0.381ns [*] - Storey 25: · ars 0: -0.12ns [*] · ars 1: -0.357ns [*] · ars 2: +0.752ns [*] · ars 3: +0.233ns [*] · ars 4: -0.138ns [*] · ars 5: -0.37ns [*] >========================================================================================< >>> Calibrating Line 10: > Section #0: Calibrating from St01 to St03 using OB 1232 (L08 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1242 (L10 S02) > Fitting for time corrections... -> Fit: offset = 2.15 slope = 0.0711 (parabola = 0.000133) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: -0.0335ns [*] · ars 1: -0.0137ns [*] · ars 2: +0.222ns [*] · ars 3: -0.175ns [*] · ars 4: -0.0374ns [*] · ars 5: -0.0464ns [*] - Storey 5: · ars 0: -1ns [*] · ars 1: -0.629ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.254ns [*] · ars 5: -0.503ns [*] - Storey 6: · ars 0: +0.956ns [*] · ars 1: +0.912ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.753ns [*] · ars 5: +0.487ns [*] - Storey 7: · ars 0: +0.209ns [*] · ars 1: +0.173ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available - Storey 8: · ars 0: -0.435ns [*] · ars 1: +0.275ns [*] · ars 2: +0.356ns [*] · ars 3: -0.264ns [*] · ars 4: -0.436ns [*] · ars 5: +0.141ns [*] - Storey 9: · ars 0: +0.47ns [*] · ars 1: +0.591ns [*] · ars 2: +0.109ns [*] · ars 3: -0.0185ns [*] · ars 4: -1.57ns [*] · ars 5: -2.84ns [ ] - Storey 10: · ars 0: -0.0748ns [*] · ars 1: +0.134ns [*] · ars 2: +0.146ns [*] · ars 3: +0.82ns [*] · ars 4: -0.747ns [*] · ars 5: -0.518ns [*] > Section #2: Calibrating from St11 to St16 using OB 1277 (L10 S09) > Fitting for time corrections... -> Fit: offset = 0.589 slope = 0.0651 (parabola = 7.12e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: -0.000251ns [*] · ars 1: -0.252ns [*] · ars 2: -0.381ns [*] · ars 3: -0.535ns [*] · ars 4: +0.684ns [*] · ars 5: -0.0291ns [*] - Storey 12: · ars 0: +0.0434ns [*] · ars 1: +0.149ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.463ns [*] · ars 5: +0.662ns [*] - Storey 13: · ars 0: -0.232ns [*] · ars 1: -0.412ns [*] · ars 2: +0.14ns [*] · ars 3: -0.343ns [*] · ars 4: -0.342ns [*] · ars 5: -0.23ns [*] - Storey 14: · ars 0: +0.0915ns [*] · ars 1: +0.158ns [*] · ars 2: -0.563ns [*] · ars 3: -0.99ns [*] · ars 4: +0.527ns [*] · ars 5: +0.641ns [*] - Storey 15: · ars 0: -0.455ns [*] · ars 1: +0.158ns [*] · ars 2: +0.975ns [*] · ars 3: +0.638ns [*] · ars 4: -0.256ns [*] · ars 5: -0.258ns [*] - Storey 16: · ars 0: +0.0115ns [*] · ars 1: +0.0535ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.493ns [*] · ars 5: +0.412ns [*] > Section #3: Calibrating from St17 to St22 using OB 1249 (L10 S15) > Fitting for time corrections... -> Fit: offset = -0.626 slope = 0.0868 (parabola = 0.00034) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.334ns [*] · ars 1: +0.629ns [*] · ars 2: -10.8ns [ ] · ars 3: -10.8ns [ ] · ars 4: -0.862ns [*] · ars 5: -0.935ns [*] - Storey 18: · ars 0: -0.659ns [*] · ars 1: -0.902ns [*] · ars 2: +0.144ns [*] · ars 3: +0.244ns [*] · ars 4: -0.3ns [*] · ars 5: -0.332ns [*] - Storey 19: · ars 0: +0.731ns [*] · ars 1: +0.992ns [*] · ars 2: +0.649ns [*] · ars 3: +0.466ns [*] · ars 4: +0.529ns [ ] · ars 5: +0.55ns [ ] - Storey 20: · ars 0: +0.129ns [*] · ars 1: +0.207ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.133ns [*] · ars 5: +0.314ns [*] - Storey 21: · ars 0: -0.304ns [*] · ars 1: +0.186ns [*] · ars 2: +0.0652ns [*] · ars 3: +0.0626ns [*] · ars 4: +0.763ns [*] · ars 5: +0.272ns [*] - Storey 22: · ars 0: -0.887ns [*] · ars 1: -0.18ns [*] · ars 2: -0.324ns [*] · ars 3: -0.536ns [*] · ars 4: +0.214ns [*] · ars 5: -0.0491ns [*] > Section #4: Calibrating from St23 to St25 using OB 1224 (L10 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 11: > Section #0: Calibrating from St01 to St03 using OB 1088 (L12 S02) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1236 (L11 S02) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #2: Calibrating from St11 to St16 using OB 1309 (L11 S09) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #3: Calibrating from St17 to St22 using OB 1272 (L11 S15) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #4: Calibrating from St23 to St25 using OB 1274 (L11 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 12: > Section #0: Calibrating from St01 to St03 using OB 1236 (L11 S02) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1088 (L12 S02) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #2: Calibrating from St11 to St16 using OB 1038 (L12 S09) > Fitting for time corrections... -> Fit: offset = -0.0841 slope = 0.0776 (parabola = 8.13e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: +0.0599ns [*] · ars 1: +0.164ns [*] · ars 2: +0.272ns [*] · ars 3: +0.112ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 12: · ars 0: -46.8ns [ ] · ars 1: +0.243ns [*] · ars 2: -1.41ns [*] · ars 3: -1.27ns [*] · ars 4: -0.127ns [*] · ars 5: -0.0323ns [*] - Storey 13: · ars 0: +0.0423ns [*] · ars 1: -0.0762ns [*] · ars 2: +0.341ns [*] · ars 3: +0.421ns [*] · ars 4: +0.4ns [*] · ars 5: +0.337ns [*] - Storey 14: · ars 0: +0.325ns [*] · ars 1: +0.351ns [*] · ars 2: -0.327ns [*] · ars 3: +0.222ns [*] · ars 4: +0.484ns [*] · ars 5: +0.802ns [*] - Storey 15: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.957ns [*] · ars 3: -1.04ns [*] · ars 4: +0.393ns [*] · ars 5: +0.447ns [*] - Storey 16: · ars 0: -0.205ns [*] · ars 1: -0.26ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.69ns [*] · ars 5: +0.015ns [ ] > Section #3: Calibrating from St17 to St22 using OB 1041 (L12 S15) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #4: Calibrating from St23 to St25 using OB 1294 (L12 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >> Report of all ERRORs: >========================================================================================< >>> Calibrating Line 1: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1631 (L01 S02) > Section #2: Calibrating from St11 to St16 using OB 1643 (L01 S09) > Section #3: Calibrating from St17 to St22 using OB 1628 (L01 S15) > Section #4: Calibrating from St23 to St25 using OB 1621 (L01 S21) >========================================================================================< >>> Calibrating Line 2: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1095 (L02 S02) > Section #2: Calibrating from St11 to St16 using OB 1048 (L02 S09) > Section #3: Calibrating from St17 to St22 using OB 1065 (L02 S15) > Section #4: Calibrating from St23 to St25 using OB 1118 (L02 S21) >========================================================================================< >>> Calibrating Line 3: > Section #0: Calibrating from St01 to St03 using OB 1193 (L05 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1027 (L03 S02) > Section #2: Calibrating from St11 to St16 using OB 1157 (L03 S09) > Section #3: Calibrating from St17 to St22 using OB 1140 (L03 S15) > Section #4: Calibrating from St23 to St25 using OB 1106 (L03 S21) >========================================================================================< >>> Calibrating Line 4: > Section #0: Calibrating from St01 to St03 using OB 1092 (L06 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1091 (L04 S02) > Section #2: Calibrating from St11 to St16 using OB 1141 (L04 S09) > Section #3: Calibrating from St17 to St22 using OB 1115 (L04 S15) > Section #4: Calibrating from St23 to St25 using OB 1151 (L04 S21) >========================================================================================< >>> Calibrating Line 5: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1193 (L05 S02) > Section #2: Calibrating from St11 to St16 using OB 1159 (L05 S09) > Section #3: Calibrating from St17 to St22 using OB 1163 (L05 S15) > Section #4: Calibrating from St23 to St25 using OB 1158 (L05 S21) >========================================================================================< >>> Calibrating Line 6: > Section #0: Calibrating from St01 to St03 using OB 1091 (L04 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1092 (L06 S02) > Section #2: Calibrating from St11 to St16 using OB 1186 (L06 S09) > Section #3: Calibrating from St17 to St22 using OB 1046 (L06 S15) > Section #4: Calibrating from St23 to St25 using OB 1056 (L06 S21) >========================================================================================< >>> Calibrating Line 7: > Section #0: Calibrating from St01 to St03 using OB 1025 (L09 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1195 (L07 S02) > Section #2: Calibrating from St11 to St16 using OB 1116 (L07 S09) > Section #3: Calibrating from St17 to St22 using OB 1042 (L07 S15) > Section #4: Calibrating from St23 to St25 using OB 1177 (L07 S21) >========================================================================================< >>> Calibrating Line 8: > Section #0: Calibrating from St01 to St03 using OB 1242 (L10 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1232 (L08 S02) > Section #2: Calibrating from St11 to St16 using OB 1176 (L08 S09) > Section #3: Calibrating from St17 to St22 using OB 1138 (L08 S15) > Section #4: Calibrating from St23 to St25 using OB 1219 (L08 S21) >========================================================================================< >>> Calibrating Line 9: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1025 (L09 S02) > Section #2: Calibrating from St11 to St16 using OB 1247 (L09 S09) > Section #3: Calibrating from St17 to St22 using OB 1068 (L09 S15) > Section #4: Calibrating from St23 to St25 using OB 1263 (L09 S21) >========================================================================================< >>> Calibrating Line 10: > Section #0: Calibrating from St01 to St03 using OB 1232 (L08 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1242 (L10 S02) > Section #2: Calibrating from St11 to St16 using OB 1277 (L10 S09) > Section #3: Calibrating from St17 to St22 using OB 1249 (L10 S15) > Section #4: Calibrating from St23 to St25 using OB 1224 (L10 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 11: > Section #0: Calibrating from St01 to St03 using OB 1088 (L12 S02) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1236 (L11 S02) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #2: Calibrating from St11 to St16 using OB 1309 (L11 S09) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #3: Calibrating from St17 to St22 using OB 1272 (L11 S15) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #4: Calibrating from St23 to St25 using OB 1274 (L11 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 12: > Section #0: Calibrating from St01 to St03 using OB 1236 (L11 S02) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1088 (L12 S02) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #2: Calibrating from St11 to St16 using OB 1038 (L12 S09) > Section #3: Calibrating from St17 to St22 using OB 1041 (L12 S15) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #4: Calibrating from St23 to St25 using OB 1294 (L12 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Finished! /////////////////////////////////////////////////////////////////////////////////////////////////////////// # LED Runes for the intermediate intraline calibration (#12F) -> START: ??/??/???? # @runes = ( "73255" ,"73251" ,"73250" ,"73249" ,"73248" ,"73247" ,"73246" ,"73245" ,"73244" ,"73243" ,"73242" ,"73241" ,"73240" ,"73239" ,"73238" ,"73237" ,"73236" ,"73235" ,"73234" ,"73233" ,"73231" ); # @date = ( 131021 ); # $runcal = "2013:V1.0";