Tuesday, October 16 2012 intratical_10D calibration new intermediate T0 set for July 2012 after 10 new intermediate T0 set for July 2012 after 10. Used T0s from 10 (OID 94617161) and runes of 30/07/2012. Log available at: "http://ific.uv.es/~agusanlo/calibrations/intratical_10D" /////////////////////////////////////////////////////////////////////////////////////////////////////////// Intraline calibration performed with standard LED-OB calibration runes of 16/01/2012: Walk correction disabled (old style), no more corrections (cross talk, etc) in consideration taken (old style) Section #0 1-3 (Not performed) Section #1 4-10 Section #2 11-16(17) Section #3 17-22(23) Section #4 23-25 Also these LED OBs were not available: L09F21 L10D21 L11S02 L11S21 L12S15 online calibration "2012:V1.0" with rigid alignment: > LABEL = "2012:V1.0" ( VERSION_ID = 95835317 ) > ARS_T0_VERSION = 94617161 > ARS_TVC_VERSION = 57889518 > ARS_AVC_0PE_VERSION = 85107924 > ARS_AVC_1PE_VERSION = 93001921 > ALIGNMENT_VERSION = 59100183 > ARS_XT_VERSION = 64970555 > old runTimeStamp = 1326692000 (Mon, 16 Jan 2012 05:33:20 +0000 (GMT) + 0 nsec) > old CLOCK_RUN_ID = 164428 > old CLOCK_CONFIGURATION_ID = 275 > new runTimeStamp = 1343606400 (Mon, 30 Jul 2012 00:00:00 +0000 (GMT) + 0 nsec) > new CLOCK_RUN_ID = 165955 > new CLOCK_CONFIGURATION_ID = 275 > Histogram Statistics T0s: > Minimum difference: -24.5499 > Maximum difference: 39.032 > Histogram Statistics CLKs: > Minimum difference: -0.058 > Maximum difference: 0.042 > Histogram Statistics T0s+CLKs: > Minimum difference: -24.5539 > Maximum difference: 39.045 new T0 ID105551472 /////////////////////////////////////////////////////////////////////////////////////////////////////////// Observations during revision of the autobinning-intratical output: Fast manual calibration (non exhaustive info) (weird reported in attached pictures) /////////////////////////////////////////////////////////////////////////////////////////////////////////// Calibration_manager Statistics after the human inspection: > Statistics: (1770 ARS) - 240 with no run (i.e. no OB) available to perform calibration. [0ns APPLIED] (LED OBs not used: L09S21 L10S21 L11S02 L11S21 L12S15 ) - 284 which their histograms don't exist. [0ns APPLIED] - 4 are an official Dead Channel not among the listed before. [0ns APPLIED] - 1177 are ready to be corrected without problems. - 14 are a pair of ARSs miscalibrated more than 1ns. [14 REVISED (100%) / 0 TOUCHÉ REMAINS] - 15 have a bad performed fit but lie in the fit zone. [15 APPLIED (100%)] - 31 lie out of the exclusion zone with a good fit performed. [31 APPLIED (100%)] - 19 lie out of the exclusion zone with a bad fit performed. [19 APPLIED (100%)] All counted sum a total of 1770 ARSs. - 0 should still be revised + 0 perfect ARS pairs. At The End: - 528 couldn't be corrected. (no data or dead channel) - 5 were decided not to be corrected. (0ns of correction) - 1237 were decided to be corrected: · 1172 less than 1ns. · 26 between 1ns and 2ns. · 21 between 2ns and 5ns. · 18 more than 5ns. - And 14 are in a pair corrected more than 1ns: · 6 less than 2ns. · 0 between 2ns and 5ns. · 8 more than 5ns. /////////////////////////////////////////////////////////////////////////////////////////////////////////// ARS that couldn't be corrected (no data or Dead Channel): L01 S01 ars0; L01 S01 ars1; L01 S01 ars2; L01 S01 ars3; L01 S01 ars4; L01 S01 ars5; L01 S02 ars0; L01 S02 ars1; L01 S02 ars2; L01 S02 ars3; L01 S02 ars4; L01 S02 ars5; L01 S03 ars0; L01 S03 ars1; L01 S03 ars2; L01 S03 ars3; L01 S03 ars4; L01 S03 ars5; L01 S04 ars0; L01 S04 ars1; ; ; ; ; ; ; L01 S05 ars2; L01 S05 ars3; ; ; L01 S06 ars0; L01 S06 ars1; ; ; ; ; L01 S07 ars0; L01 S07 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L01 S11 ars2; L01 S11 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L01 S14 ars0; L01 S14 ars1; ; ; ; ; ; ; L01 S15 ars2; L01 S15 ars3; ; ; ; ; ; ; L01 S16 ars4; L01 S16 ars5; ; ; ; ; ; ; ; ; L01 S18 ars2; L01 S18 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L01 S22 ars2; L01 S22 ars3; ; ; ; ; ; ; ; ; ; ; ; ; L01 S24 ars4; L01 S24 ars5; ; ; ; ; ; ; L02 S01 ars0; L02 S01 ars1; L02 S01 ars2; L02 S01 ars3; L02 S01 ars4; L02 S01 ars5; L02 S02 ars0; L02 S02 ars1; L02 S02 ars2; L02 S02 ars3; L02 S02 ars4; L02 S02 ars5; L02 S03 ars0; L02 S03 ars1; L02 S03 ars2; L02 S03 ars3; L02 S03 ars4; L02 S03 ars5; L02 S04 ars0; L02 S04 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L02 S07 ars0; L02 S07 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L02 S10 ars0; L02 S10 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L02 S19 ars4; L02 S19 ars5; ; ; ; ; ; ; ; ; ; ; ; ; L02 S22 ars0; L02 S22 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L03 S01 ars0; L03 S01 ars1; L03 S01 ars2; L03 S01 ars3; L03 S01 ars4; L03 S01 ars5; L03 S02 ars0; L03 S02 ars1; L03 S02 ars2; L03 S02 ars3; L03 S02 ars4; L03 S02 ars5; L03 S03 ars0; L03 S03 ars1; L03 S03 ars2; L03 S03 ars3; L03 S03 ars4; L03 S03 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L03 S09 ars2; L03 S09 ars3; ; ; ; ; ; ; ; ; L03 S11 ars0; L03 S11 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L03 S17 ars2; L03 S17 ars3; ; ; ; ; ; ; L03 S18 ars4; L03 S18 ars5; ; ; ; ; L03 S19 ars4; L03 S19 ars5; ; ; ; ; ; ; ; ; L03 S21 ars2; L03 S21 ars3; ; ; ; ; ; ; L03 S22 ars4; L03 S22 ars5; ; ; ; ; ; ; ; ; ; ; ; ; L03 S25 ars0; L03 S25 ars1; ; ; ; ; L04 S01 ars0; L04 S01 ars1; L04 S01 ars2; L04 S01 ars3; L04 S01 ars4; L04 S01 ars5; L04 S02 ars0; L04 S02 ars1; L04 S02 ars2; L04 S02 ars3; L04 S02 ars4; L04 S02 ars5; L04 S03 ars0; L04 S03 ars1; L04 S03 ars2; L04 S03 ars3; L04 S03 ars4; L04 S03 ars5; ; ; L04 S04 ars2; L04 S04 ars3; ; ; ; ; ; ; L04 S05 ars4; L04 S05 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L04 S12 ars0; L04 S12 ars1; ; ; L04 S12 ars4; L04 S12 ars5; ; ; ; ; ; ; ; ; L04 S14 ars2; L04 S14 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L04 S17 ars4; L04 S17 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L05 S01 ars0; L05 S01 ars1; L05 S01 ars2; L05 S01 ars3; L05 S01 ars4; L05 S01 ars5; L05 S02 ars0; L05 S02 ars1; L05 S02 ars2; L05 S02 ars3; L05 S02 ars4; L05 S02 ars5; L05 S03 ars0; L05 S03 ars1; L05 S03 ars2; L05 S03 ars3; L05 S03 ars4; L05 S03 ars5; ; ; ; ; L05 S04 ars4; L05 S04 ars5; ; ; ; ; L05 S05 ars4; L05 S05 ars5; ; ; ; ; ; ; L05 S07 ars0; L05 S07 ars1; ; ; ; ; ; ; L05 S08 ars2; L05 S08 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L05 S11 ars4; L05 S11 ars5; L05 S12 ars0; L05 S12 ars1; ; ; ; ; ; ; L05 S13 ars2; L05 S13 ars3; ; ; ; ; L05 S14 ars2; L05 S14 ars3; ; ; ; ; ; ; ; ; L05 S16 ars0; L05 S16 ars1; L05 S16 ars2; L05 S16 ars3; L05 S16 ars4; L05 S16 ars5; ; ; ; ; ; ; ; ; ; ; ; ; L05 S19 ars0; L05 S19 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L05 S22 ars4; L05 S22 ars5; ; ; ; ; ; ; L05 S24 ars0; L05 S24 ars1; L05 S24 ars2; L05 S24 ars3; ; ; L05 S25 ars0; L05 S25 ars1; ; ; L05 S25 ars4; L05 S25 ars5; L06 S01 ars0; L06 S01 ars1; L06 S01 ars2; L06 S01 ars3; L06 S01 ars4; L06 S01 ars5; L06 S02 ars0; L06 S02 ars1; L06 S02 ars2; L06 S02 ars3; L06 S02 ars4; L06 S02 ars5; L06 S03 ars0; L06 S03 ars1; L06 S03 ars2; L06 S03 ars3; L06 S03 ars4; L06 S03 ars5; ; ; ; ; L06 S04 ars4; L06 S04 ars5; L06 S05 ars0; L06 S05 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L06 S16 ars2; L06 S16 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L06 S22 ars2; L06 S22 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L06 S25 ars4; L06 S25 ars5; L07 S01 ars0; L07 S01 ars1; L07 S01 ars2; L07 S01 ars3; L07 S01 ars4; L07 S01 ars5; L07 S02 ars0; L07 S02 ars1; L07 S02 ars2; L07 S02 ars3; L07 S02 ars4; L07 S02 ars5; L07 S03 ars0; L07 S03 ars1; L07 S03 ars2; L07 S03 ars3; L07 S03 ars4; L07 S03 ars5; ; ; L07 S04 ars2; L07 S04 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L07 S11 ars0; L07 S11 ars1; ; ; L07 S11 ars4; L07 S11 ars5; ; ; ; ; L07 S12 ars4; L07 S12 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L07 S16 ars0; L07 S16 ars1; L07 S16 ars2; L07 S16 ars3; ; ; L07 S17 ars0; L07 S17 ars1; ; ; ; ; ; ; ; ; ; ; ; ; L07 S19 ars2; L07 S19 ars3; ; ; L07 S20 ars0; L07 S20 ars1; L07 S20 ars2; L07 S20 ars3; ; ; ; ; ; ; L07 S21 ars4; L07 S21 ars5; L07 S22 ars0; L07 S22 ars1; ; ; ; ; ; ; ; ; L07 S23 ars4; L07 S23 ars5; ; ; ; ; ; ; ; ; L07 S25 ars2; L07 S25 ars3; ; ; L08 S01 ars0; L08 S01 ars1; L08 S01 ars2; L08 S01 ars3; L08 S01 ars4; L08 S01 ars5; L08 S02 ars0; L08 S02 ars1; L08 S02 ars2; L08 S02 ars3; L08 S02 ars4; L08 S02 ars5; L08 S03 ars0; L08 S03 ars1; L08 S03 ars2; L08 S03 ars3; L08 S03 ars4; L08 S03 ars5; ; ; ; ; ; ; ; ; ; ; ; ; L08 S06 ars0; L08 S06 ars1; ; ; ; ; ; ; ; ; L08 S07 ars4; L08 S07 ars5; ; ; ; ; ; ; ; ; ; ; L08 S09 ars4; L08 S09 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L08 S15 ars0; L08 S15 ars1; ; ; ; ; ; ; ; ; ; ; L08 S17 ars0; L08 S17 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L08 S20 ars4; L08 S20 ars5; ; ; L08 S21 ars2; L08 S21 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L09 S01 ars0; L09 S01 ars1; L09 S01 ars2; L09 S01 ars3; L09 S01 ars4; L09 S01 ars5; L09 S02 ars0; L09 S02 ars1; L09 S02 ars2; L09 S02 ars3; L09 S02 ars4; L09 S02 ars5; L09 S03 ars0; L09 S03 ars1; L09 S03 ars2; L09 S03 ars3; L09 S03 ars4; L09 S03 ars5; ; ; ; ; ; ; L09 S05 ars0; L09 S05 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L09 S11 ars4; L09 S11 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L09 S18 ars2; L09 S18 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L09 S23 ars0; L09 S23 ars1; L09 S23 ars2; L09 S23 ars3; L09 S23 ars4; L09 S23 ars5; L09 S24 ars0; L09 S24 ars1; L09 S24 ars2; L09 S24 ars3; L09 S24 ars4; L09 S24 ars5; L09 S25 ars0; L09 S25 ars1; L09 S25 ars2; L09 S25 ars3; L09 S25 ars4; L09 S25 ars5; L10 S01 ars0; L10 S01 ars1; L10 S01 ars2; L10 S01 ars3; L10 S01 ars4; L10 S01 ars5; L10 S02 ars0; L10 S02 ars1; L10 S02 ars2; L10 S02 ars3; L10 S02 ars4; L10 S02 ars5; L10 S03 ars0; L10 S03 ars1; L10 S03 ars2; L10 S03 ars3; L10 S03 ars4; L10 S03 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L10 S07 ars2; L10 S07 ars3; L10 S07 ars4; L10 S07 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L10 S12 ars2; L10 S12 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L10 S20 ars2; L10 S20 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L10 S23 ars0; L10 S23 ars1; L10 S23 ars2; L10 S23 ars3; L10 S23 ars4; L10 S23 ars5; L10 S24 ars0; L10 S24 ars1; L10 S24 ars2; L10 S24 ars3; L10 S24 ars4; L10 S24 ars5; L10 S25 ars0; L10 S25 ars1; L10 S25 ars2; L10 S25 ars3; L10 S25 ars4; L10 S25 ars5; L11 S01 ars0; L11 S01 ars1; L11 S01 ars2; L11 S01 ars3; L11 S01 ars4; L11 S01 ars5; L11 S02 ars0; L11 S02 ars1; L11 S02 ars2; L11 S02 ars3; L11 S02 ars4; L11 S02 ars5; L11 S03 ars0; L11 S03 ars1; L11 S03 ars2; L11 S03 ars3; L11 S03 ars4; L11 S03 ars5; L11 S04 ars0; L11 S04 ars1; L11 S04 ars2; L11 S04 ars3; L11 S04 ars4; L11 S04 ars5; L11 S05 ars0; L11 S05 ars1; L11 S05 ars2; L11 S05 ars3; L11 S05 ars4; L11 S05 ars5; L11 S06 ars0; L11 S06 ars1; L11 S06 ars2; L11 S06 ars3; L11 S06 ars4; L11 S06 ars5; L11 S07 ars0; L11 S07 ars1; L11 S07 ars2; L11 S07 ars3; L11 S07 ars4; L11 S07 ars5; L11 S08 ars0; L11 S08 ars1; L11 S08 ars2; L11 S08 ars3; L11 S08 ars4; L11 S08 ars5; L11 S09 ars0; L11 S09 ars1; L11 S09 ars2; L11 S09 ars3; L11 S09 ars4; L11 S09 ars5; L11 S10 ars0; L11 S10 ars1; L11 S10 ars2; L11 S10 ars3; L11 S10 ars4; L11 S10 ars5; L11 S11 ars0; L11 S11 ars1; ; ; ; ; ; ; L11 S12 ars2; L11 S12 ars3; ; ; ; ; ; ; L11 S13 ars4; L11 S13 ars5; ; ; L11 S14 ars2; L11 S14 ars3; L11 S14 ars4; L11 S14 ars5; ; ; L11 S15 ars2; L11 S15 ars3; L11 S15 ars4; L11 S15 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L11 S20 ars2; L11 S20 ars3; ; ; ; ; L11 S21 ars2; L11 S21 ars3; L11 S21 ars4; L11 S21 ars5; ; ; ; ; ; ; L11 S23 ars0; L11 S23 ars1; L11 S23 ars2; L11 S23 ars3; L11 S23 ars4; L11 S23 ars5; L11 S24 ars0; L11 S24 ars1; L11 S24 ars2; L11 S24 ars3; L11 S24 ars4; L11 S24 ars5; L11 S25 ars0; L11 S25 ars1; L11 S25 ars2; L11 S25 ars3; L11 S25 ars4; L11 S25 ars5; L12 S01 ars0; L12 S01 ars1; L12 S01 ars2; L12 S01 ars3; L12 S01 ars4; L12 S01 ars5; L12 S02 ars0; L12 S02 ars1; L12 S02 ars2; L12 S02 ars3; L12 S02 ars4; L12 S02 ars5; L12 S03 ars0; L12 S03 ars1; L12 S03 ars2; L12 S03 ars3; L12 S03 ars4; L12 S03 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L12 S07 ars4; L12 S07 ars5; ; ; ; ; L12 S08 ars4; L12 S08 ars5; ; ; ; ; ; ; L12 S10 ars0; L12 S10 ars1; ; ; ; ; ; ; ; ; L12 S11 ars4; L12 S11 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L12 S15 ars0; L12 S15 ars1; ; ; ; ; ; ; L12 S16 ars2; L12 S16 ars3; ; ; L12 S17 ars0; L12 S17 ars1; L12 S17 ars2; L12 S17 ars3; L12 S17 ars4; L12 S17 ars5; L12 S18 ars0; L12 S18 ars1; L12 S18 ars2; L12 S18 ars3; L12 S18 ars4; L12 S18 ars5; L12 S19 ars0; L12 S19 ars1; L12 S19 ars2; L12 S19 ars3; L12 S19 ars4; L12 S19 ars5; L12 S20 ars0; L12 S20 ars1; L12 S20 ars2; L12 S20 ars3; L12 S20 ars4; L12 S20 ars5; /////////////////////////////////////////////////////////////////////////////////////////////////////////// Execution of intratical program: evalu155:agusanlo/macros/tical> ./intratical -i /l/agusanlo/data/tical/intratical_10D/autobinning -o /l/agusanlo/data/tical/intratical_10D > Searching OB available... ID: 1628 (L01 S15) [ 1 run ] ID: 1631 (L01 S02) [ 1 run ] ID: 1621 (L01 S21) [ 1 run ] ID: 1643 (L01 S09) [ 1 run ] ID: 1065 (L02 S15) [ 1 run ] ID: 1095 (L02 S02) [ 1 run ] ID: 1118 (L02 S21) [ 1 run ] ID: 1048 (L02 S09) [ 1 run ] ID: 1140 (L03 S15) [ 1 run ] ID: 1027 (L03 S02) [ 1 run ] ID: 1106 (L03 S21) [ 1 run ] ID: 1157 (L03 S09) [ 1 run ] ID: 1115 (L04 S15) [ 1 run ] ID: 1091 (L04 S02) [ 1 run ] ID: 1151 (L04 S21) [ 1 run ] ID: 1141 (L04 S09) [ 1 run ] ID: 1163 (L05 S15) [ 1 run ] ID: 1193 (L05 S02) [ 1 run ] ID: 1158 (L05 S21) [ 1 run ] ID: 1159 (L05 S09) [ 1 run ] ID: 1046 (L06 S15) [ 1 run ] ID: 1092 (L06 S02) [ 1 run ] ID: 1056 (L06 S21) [ 1 run ] ID: 1186 (L06 S09) [ 1 run ] ID: 1042 (L07 S15) [ 1 run ] ID: 1195 (L07 S02) [ 1 run ] ID: 1177 (L07 S21) [ 1 run ] ID: 1116 (L07 S09) [ 1 run ] ID: 1138 (L08 S15) [ 1 run ] ID: 1232 (L08 S02) [ 1 run ] ID: 1219 (L08 S21) [ 1 run ] ID: 1176 (L08 S09) [ 1 run ] ID: 1068 (L09 S15) [ 1 run ] ID: 1025 (L09 S02) [ 1 run ] ID: 1247 (L09 S09) [ 1 run ] ID: 1249 (L10 S15) [ 1 run ] ID: 1242 (L10 S02) [ 1 run ] ID: 1277 (L10 S09) [ 1 run ] ID: 1272 (L11 S15) [ 1 run ] ID: 1309 (L11 S09) [ 1 run ] ID: 1088 (L12 S02) [ 1 run ] ID: 1038 (L12 S09) [ 1 run ] > Found 42 OBs! (in a total of 24 runes) >========================================================================================< >>> Calibrating Line 1: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > Reading TTree... > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1631 (L01 S02) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -3.76 slope = 0.113 (parabola = 5.3e-06) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.271ns [*] · ars 3: -0.262ns [*] · ars 4: -0.51ns [*] · ars 5: -0.394ns [*] - Storey 5: · ars 0: +1.47ns [*] · ars 1: +1.61ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.0667ns [*] · ars 5: +0.18ns [*] - Storey 6: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.385ns [*] · ars 3: -0.36ns [*] · ars 4: -0.559ns [*] · ars 5: -0.366ns [*] - Storey 7: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.588ns [*] · ars 3: -0.533ns [*] · ars 4: +0.0717ns [*] · ars 5: +0.241ns [*] - Storey 8: · ars 0: +0.0762ns [*] · ars 1: +0.000497ns [*] · ars 2: -0.0725ns [*] · ars 3: -0.0509ns [*] · ars 4: +0.239ns [*] · ars 5: +0.297ns [*] - Storey 9: · ars 0: -0.0536ns [*] · ars 1: -0.0794ns [*] · ars 2: -0.242ns [*] · ars 3: +0.0394ns [*] · ars 4: +0.273ns [*] · ars 5: +0.171ns [*] - Storey 10: · ars 0: -0.233ns [*] · ars 1: +0.0876ns [*] · ars 2: +0.404ns [*] · ars 3: +0.277ns [*] · ars 4: -0.229ns [*] · ars 5: -0.316ns [*] > Section #2: Calibrating from St11 to St16 using OB 1643 (L01 S09) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -0.274 slope = 0.0926 (parabola = -6.27e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: +0.128ns [*] · ars 1: +0.0235ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.0131ns [*] · ars 5: -0.0906ns [*] - Storey 12: · ars 0: +0.0952ns [*] · ars 1: +0.134ns [*] · ars 2: +0.0649ns [*] · ars 3: +0.0797ns [*] · ars 4: -0.133ns [*] · ars 5: -0.0369ns [*] - Storey 13: · ars 0: +0.0162ns [*] · ars 1: +0.0771ns [*] · ars 2: -0.00748ns [*] · ars 3: +0.0607ns [*] · ars 4: +0.317ns [*] · ars 5: +0.0694ns [*] - Storey 14: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.622ns [*] · ars 3: -0.094ns [*] · ars 4: -0.238ns [*] · ars 5: -0.22ns [*] - Storey 15: · ars 0: +0.036ns [*] · ars 1: +0.125ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.016ns [*] · ars 5: +0.00123ns [*] - Storey 16: · ars 0: -0.00274ns [*] · ars 1: -0.0861ns [*] · ars 2: -0.191ns [*] · ars 3: +0.00775ns [*] · ars 4: Not Available · ars 5: Not Available > Section #3: Calibrating from St17 to St22 using OB 1628 (L01 S15) > Reading TTree... > Fitting for time corrections... -> Fit: offset = 0.4 slope = 0.0889 (parabola = -2.22e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.0293ns [*] · ars 1: +0.133ns [*] · ars 2: -0.052ns [*] · ars 3: -0.461ns [*] · ars 4: +0.258ns [*] · ars 5: +0.245ns [*] - Storey 18: · ars 0: +0.4ns [*] · ars 1: +0.0255ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.3ns [*] · ars 5: -0.0228ns [*] - Storey 19: · ars 0: -0.35ns [*] · ars 1: -0.247ns [*] · ars 2: +0.175ns [*] · ars 3: +0.0931ns [*] · ars 4: -0.66ns [*] · ars 5: -0.439ns [*] - Storey 20: · ars 0: -0.186ns [*] · ars 1: -0.465ns [*] · ars 2: +0.171ns [*] · ars 3: +0.332ns [*] · ars 4: +0.255ns [*] · ars 5: -0.172ns [*] - Storey 21: · ars 0: +0.19ns [*] · ars 1: -0.0777ns [*] · ars 2: +0.553ns [*] · ars 3: +0.0526ns [*] · ars 4: -0.229ns [*] · ars 5: +0.133ns [*] - Storey 22: · ars 0: +0.099ns [*] · ars 1: +0.276ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.125ns [*] · ars 5: -0.0214ns [*] > Section #4: Calibrating from St23 to St25 using OB 1621 (L01 S21) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -1.31 slope = 0.111 (parabola = 0.000539) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: +0.168ns [*] · ars 1: +0.102ns [*] · ars 2: -0.0375ns [*] · ars 3: +0.00783ns [*] · ars 4: -0.235ns [*] · ars 5: -0.176ns [*] - Storey 24: · ars 0: +0.106ns [*] · ars 1: +0.152ns [*] · ars 2: +0.109ns [*] · ars 3: -0.0251ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 25: · ars 0: +0.0181ns [*] · ars 1: +0.0877ns [*] · ars 2: -0.0979ns [*] · ars 3: +0.0624ns [*] · ars 4: -0.0443ns [*] · ars 5: -0.197ns [*] >========================================================================================< >>> Calibrating Line 2: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > Reading TTree... > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1095 (L02 S02) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -1.92 slope = 0.0563 (parabola = 0.00021) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.385ns [*] · ars 3: -0.371ns [ ] · ars 4: -0.0263ns [*] · ars 5: -0.145ns [*] - Storey 5: · ars 0: -0.528ns [*] · ars 1: -0.313ns [*] · ars 2: +0.358ns [*] · ars 3: -0.179ns [*] · ars 4: -0.296ns [*] · ars 5: -0.113ns [*] - Storey 6: · ars 0: +0.531ns [*] · ars 1: +0.536ns [*] · ars 2: +0.537ns [*] · ars 3: +0.288ns [*] · ars 4: +0.0609ns [*] · ars 5: +0.248ns [*] - Storey 7: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.184ns [*] · ars 3: -0.292ns [*] · ars 4: -0.12ns [*] · ars 5: -0.0733ns [*] - Storey 8: · ars 0: +0.00664ns [*] · ars 1: +0.481ns [*] · ars 2: +0.768ns [*] · ars 3: +0.816ns [*] · ars 4: -0.0804ns [*] · ars 5: -0.0695ns [*] - Storey 9: · ars 0: +2.83ns [ ] · ars 1: +2.18ns [ ] · ars 2: -0.575ns [*] · ars 3: -0.309ns [*] · ars 4: -0.583ns [*] · ars 5: -0.477ns [*] - Storey 10: · ars 0: Not Available · ars 1: Not Available · ars 2: -10.8ns [ ] · ars 3: -24ns [ ] · ars 4: -0.201ns [*] · ars 5: +0.319ns [*] > Section #2: Calibrating from St11 to St16 using OB 1048 (L02 S09) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -1.25 slope = 0.0683 (parabola = 8.94e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: -0.106ns [*] · ars 1: -0.164ns [*] · ars 2: -0.202ns [*] · ars 3: -0.367ns [*] · ars 4: -0.173ns [*] · ars 5: -0.318ns [*] - Storey 12: · ars 0: -0.00658ns [*] · ars 1: +0.197ns [*] · ars 2: +0.179ns [*] · ars 3: +0.112ns [*] · ars 4: +0.242ns [*] · ars 5: +0.402ns [*] - Storey 13: · ars 0: +0.12ns [*] · ars 1: +0.305ns [*] · ars 2: -0.524ns [*] · ars 3: -0.592ns [*] · ars 4: +0.385ns [*] · ars 5: +0.242ns [*] - Storey 14: · ars 0: +0.2ns [*] · ars 1: +0.144ns [*] · ars 2: +0.385ns [*] · ars 3: +0.201ns [*] · ars 4: +0.0934ns [*] · ars 5: +0.152ns [*] - Storey 15: · ars 0: +0.104ns [*] · ars 1: +0.116ns [*] · ars 2: +0.318ns [*] · ars 3: -0.0896ns [*] · ars 4: +0.138ns [*] · ars 5: +0.21ns [*] - Storey 16: · ars 0: -1.32ns [*] · ars 1: -1.62ns [*] · ars 2: -0.0398ns [*] · ars 3: -0.49ns [*] · ars 4: +0.377ns [*] · ars 5: +0.587ns [*] > Section #3: Calibrating from St17 to St22 using OB 1065 (L02 S15) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -0.788 slope = 0.0667 (parabola = -0.00035) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.496ns [*] · ars 1: +0.814ns [*] · ars 2: -0.0144ns [*] · ars 3: -0.126ns [*] · ars 4: +0.339ns [*] · ars 5: +0.186ns [*] - Storey 18: · ars 0: +0.403ns [*] · ars 1: +0.407ns [*] · ars 2: -0.168ns [*] · ars 3: -0.525ns [*] · ars 4: +0.162ns [*] · ars 5: +0.4ns [*] - Storey 19: · ars 0: -0.0655ns [*] · ars 1: -0.454ns [*] · ars 2: -0.421ns [*] · ars 3: -0.173ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 20: · ars 0: -0.543ns [*] · ars 1: -0.0993ns [*] · ars 2: -1.1ns [*] · ars 3: -1.22ns [*] · ars 4: -2.29ns [ ] · ars 5: -2.14ns [ ] - Storey 21: · ars 0: -0.226ns [*] · ars 1: -0.191ns [*] · ars 2: -0.0603ns [*] · ars 3: -0.137ns [*] · ars 4: +0.552ns [*] · ars 5: -0.0365ns [*] - Storey 22: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.214ns [*] · ars 3: +0.33ns [*] · ars 4: -0.206ns [*] · ars 5: +0.0459ns [*] > Section #4: Calibrating from St23 to St25 using OB 1118 (L02 S21) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -8.3 slope = 0.176 (parabola = -0.000618) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: -0.131ns [*] · ars 1: -0.258ns [*] · ars 2: +0.0348ns [*] · ars 3: +0.244ns [*] · ars 4: +0.193ns [*] · ars 5: +0.176ns [*] - Storey 24: · ars 0: +0.162ns [*] · ars 1: -0.0226ns [*] · ars 2: -0.113ns [*] · ars 3: -0.06ns [*] · ars 4: -0.168ns [*] · ars 5: -0.317ns [*] - Storey 25: · ars 0: -0.188ns [*] · ars 1: +0.0476ns [*] · ars 2: +0.0731ns [*] · ars 3: +0.0501ns [*] · ars 4: +0.00753ns [*] · ars 5: +0.27ns [*] >========================================================================================< >>> Calibrating Line 3: > Section #0: Calibrating from St01 to St03 using OB 1193 (L05 S02) > Reading TTree... > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1027 (L03 S02) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -4.15 slope = 0.0795 (parabola = -6.1e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: -0.0191ns [*] · ars 1: -0.17ns [*] · ars 2: -0.443ns [*] · ars 3: -0.267ns [*] · ars 4: -0.146ns [*] · ars 5: +0.0018ns [*] - Storey 5: · ars 0: +0.405ns [*] · ars 1: +0.235ns [*] · ars 2: +0.495ns [*] · ars 3: +0.402ns [*] · ars 4: +0.321ns [*] · ars 5: +0.288ns [*] - Storey 6: · ars 0: +0.338ns [*] · ars 1: +0.00967ns [*] · ars 2: -0.215ns [*] · ars 3: -0.0425ns [*] · ars 4: -0.0575ns [*] · ars 5: +0.196ns [*] - Storey 7: · ars 0: -4.75ns [ ] · ars 1: -6.04ns [ ] · ars 2: +0.0386ns [*] · ars 3: +0.172ns [*] · ars 4: -0.463ns [*] · ars 5: -0.341ns [*] - Storey 8: · ars 0: +0.599ns [*] · ars 1: +0.439ns [*] · ars 2: -0.927ns [*] · ars 3: -0.974ns [*] · ars 4: -0.856ns [*] · ars 5: -0.652ns [*] - Storey 9: · ars 0: +0.229ns [*] · ars 1: +0.403ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.55ns [*] · ars 5: -0.0445ns [*] - Storey 10: · ars 0: +0.0646ns [*] · ars 1: +0.214ns [*] · ars 2: +0.0965ns [*] · ars 3: +0.453ns [*] · ars 4: -0.374ns [*] · ars 5: +0.0405ns [*] > Section #2: Calibrating from St11 to St16 using OB 1157 (L03 S09) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -5.37 slope = 0.0688 (parabola = -6.34e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.108ns [*] · ars 3: +0.321ns [*] · ars 4: -0.132ns [*] · ars 5: -0.284ns [*] - Storey 12: · ars 0: +0.254ns [*] · ars 1: +0.142ns [*] · ars 2: +0.095ns [*] · ars 3: +0.027ns [*] · ars 4: +0.0119ns [*] · ars 5: +0.0554ns [*] - Storey 13: · ars 0: -0.0816ns [*] · ars 1: +0.0177ns [*] · ars 2: +0.517ns [*] · ars 3: +0.538ns [*] · ars 4: -0.547ns [*] · ars 5: -0.732ns [*] - Storey 14: · ars 0: -0.155ns [*] · ars 1: -0.0288ns [*] · ars 2: -94.9ns [ ] · ars 3: -94.7ns [ ] · ars 4: -0.311ns [*] · ars 5: -0.125ns [*] - Storey 15: · ars 0: -0.148ns [*] · ars 1: -0.0533ns [*] · ars 2: +8.97ns [ ] · ars 3: +8.32ns [ ] · ars 4: +0.181ns [*] · ars 5: -0.0816ns [*] - Storey 16: · ars 0: -0.0744ns [*] · ars 1: -0.378ns [*] · ars 2: +0.6ns [*] · ars 3: +0.422ns [*] · ars 4: -0.0564ns [*] · ars 5: -0.302ns [*] > Section #3: Calibrating from St17 to St22 using OB 1140 (L03 S15) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -5.22 slope = 0.0689 (parabola = 7.59e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: -0.109ns [*] · ars 1: -0.213ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.0921ns [*] · ars 5: -0.148ns [*] - Storey 18: · ars 0: -0.0202ns [*] · ars 1: +0.062ns [*] · ars 2: +0.00705ns [*] · ars 3: +0.212ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 19: · ars 0: -0.00403ns [*] · ars 1: +0.29ns [*] · ars 2: +0.0577ns [*] · ars 3: -0.051ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 20: · ars 0: +0.225ns [*] · ars 1: +0.269ns [*] · ars 2: +0.257ns [*] · ars 3: +0.417ns [*] · ars 4: -0.362ns [*] · ars 5: -0.354ns [*] - Storey 21: · ars 0: +0.618ns [ ] · ars 1: +0.202ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.487ns [*] · ars 5: -0.193ns [*] - Storey 22: · ars 0: +0.189ns [*] · ars 1: +0.0349ns [*] · ars 2: +0.0184ns [*] · ars 3: +0.262ns [*] · ars 4: Not Available · ars 5: Not Available > Section #4: Calibrating from St23 to St25 using OB 1106 (L03 S21) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -10.1 slope = 0.206 (parabola = -0.000136) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: -0.275ns [*] · ars 1: -0.213ns [*] · ars 2: +0.243ns [*] · ars 3: +0.0265ns [*] · ars 4: +0.261ns [*] · ars 5: +0.01ns [*] - Storey 24: · ars 0: -0.0839ns [*] · ars 1: -0.175ns [*] · ars 2: -0.0227ns [*] · ars 3: +0.251ns [*] · ars 4: +0.016ns [*] · ars 5: -0.0919ns [*] - Storey 25: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.101ns [*] · ars 3: -0.395ns [*] · ars 4: +0.0707ns [*] · ars 5: +0.276ns [*] >========================================================================================< >>> Calibrating Line 4: > Section #0: Calibrating from St01 to St03 using OB 1092 (L06 S02) > Reading TTree... > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1091 (L04 S02) > Reading TTree... > Fitting for time corrections... -> Fit: offset = 1.18 slope = 0.00633 (parabola = 0.000333) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: +0.0116ns [*] · ars 1: -0.028ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.735ns [*] · ars 5: -0.656ns [*] - Storey 5: · ars 0: +0.065ns [*] · ars 1: +0.00918ns [*] · ars 2: -0.0625ns [*] · ars 3: +0.0168ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 6: · ars 0: -0.0354ns [*] · ars 1: +0.426ns [*] · ars 2: -1.33ns [ ] · ars 3: -1.08ns [ ] · ars 4: +0.0806ns [*] · ars 5: -0.0489ns [*] - Storey 7: · ars 0: -1.84ns [ ] · ars 1: -60.7ns [ ] · ars 2: -0.00132ns [*] · ars 3: +0.144ns [*] · ars 4: +0.638ns [*] · ars 5: +0.578ns [*] - Storey 8: · ars 0: +0.519ns [*] · ars 1: +0.683ns [ ] · ars 2: +0.32ns [*] · ars 3: +0.00389ns [*] · ars 4: -0.171ns [*] · ars 5: -0.142ns [*] - Storey 9: · ars 0: +0.0295ns [*] · ars 1: -0.284ns [*] · ars 2: +0.726ns [*] · ars 3: +0.7ns [*] · ars 4: +0.31ns [*] · ars 5: -0.00584ns [*] - Storey 10: · ars 0: -0.537ns [*] · ars 1: -0.758ns [*] · ars 2: -0.543ns [*] · ars 3: -1.23ns [*] · ars 4: +0.42ns [*] · ars 5: +0.235ns [*] > Section #2: Calibrating from St11 to St16 using OB 1141 (L04 S09) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -2.41 slope = 0.0895 (parabola = 0.00036) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: -1.26ns [*] · ars 1: -0.651ns [*] · ars 2: +0.173ns [*] · ars 3: +0.123ns [*] · ars 4: +0.0629ns [*] · ars 5: +0.0165ns [*] - Storey 12: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.352ns [*] · ars 3: +0.139ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 13: · ars 0: -0.304ns [*] · ars 1: -0.402ns [*] · ars 2: -0.0438ns [*] · ars 3: +0.0124ns [*] · ars 4: +0.0673ns [*] · ars 5: +0.0373ns [*] - Storey 14: · ars 0: +0.231ns [*] · ars 1: +0.505ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.147ns [*] · ars 5: +0.369ns [*] - Storey 15: · ars 0: -0.491ns [*] · ars 1: -0.222ns [*] · ars 2: +1.12ns [*] · ars 3: +0.223ns [*] · ars 4: +1ns [*] · ars 5: +0.691ns [*] - Storey 16: · ars 0: -0.0709ns [*] · ars 1: -0.0832ns [*] · ars 2: -0.0239ns [*] · ars 3: +0.439ns [*] · ars 4: +0.148ns [*] · ars 5: +0.452ns [*] > Section #3: Calibrating from St17 to St22 using OB 1115 (L04 S15) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -3.35 slope = 0.0795 (parabola = 5.85e-07) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.127ns [*] · ars 1: -0.13ns [*] · ars 2: -0.312ns [*] · ars 3: -0.122ns [*] · ars 4: +0.699ns [ ] · ars 5: -45.9ns [ ] - Storey 18: · ars 0: -0.308ns [*] · ars 1: -0.249ns [*] · ars 2: +0.208ns [*] · ars 3: +0.368ns [*] · ars 4: +0.504ns [*] · ars 5: +0.127ns [*] - Storey 19: · ars 0: -0.396ns [*] · ars 1: -0.385ns [*] · ars 2: +0.176ns [*] · ars 3: +0.427ns [*] · ars 4: +0.218ns [*] · ars 5: +0.208ns [*] - Storey 20: · ars 0: +0.0784ns [*] · ars 1: -0.0628ns [*] · ars 2: +0.172ns [*] · ars 3: +0.33ns [*] · ars 4: -0.324ns [*] · ars 5: -0.219ns [*] - Storey 21: · ars 0: +0.528ns [*] · ars 1: +0.292ns [*] · ars 2: -1.32ns [*] · ars 3: -0.584ns [*] · ars 4: -0.16ns [*] · ars 5: -0.145ns [*] - Storey 22: · ars 0: +0.323ns [*] · ars 1: +0.41ns [*] · ars 2: -0.32ns [*] · ars 3: +0.0344ns [*] · ars 4: +0.225ns [*] · ars 5: +0.565ns [*] > Section #4: Calibrating from St23 to St25 using OB 1151 (L04 S21) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -4.81 slope = 0.145 (parabola = 0.000601) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: -0.267ns [*] · ars 1: +0.0584ns [*] · ars 2: -0.245ns [*] · ars 3: -0.0825ns [*] · ars 4: +0.128ns [*] · ars 5: +0.155ns [*] - Storey 24: · ars 0: +0.0843ns [*] · ars 1: +0.195ns [*] · ars 2: -0.0315ns [*] · ars 3: -0.121ns [*] · ars 4: +0.108ns [*] · ars 5: +0.272ns [*] - Storey 25: · ars 0: -0.298ns [*] · ars 1: -0.257ns [*] · ars 2: -0.0241ns [*] · ars 3: -0.0622ns [*] · ars 4: +0.185ns [*] · ars 5: +0.204ns [*] >========================================================================================< >>> Calibrating Line 5: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > Reading TTree... > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1193 (L05 S02) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -6.56 slope = 0.0688 (parabola = 0.000171) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: -0.161ns [*] · ars 1: -0.214ns [*] · ars 2: -0.285ns [*] · ars 3: -0.399ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 5: · ars 0: -0.0265ns [*] · ars 1: +0.169ns [*] · ars 2: -0.0798ns [*] · ars 3: -0.0164ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 6: · ars 0: +0.0923ns [*] · ars 1: -0.0401ns [*] · ars 2: +0.196ns [*] · ars 3: +0.272ns [*] · ars 4: +0.24ns [*] · ars 5: +0.0294ns [*] - Storey 7: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.227ns [*] · ars 3: +0.265ns [*] · ars 4: +0.259ns [*] · ars 5: +0.116ns [*] - Storey 8: · ars 0: +0.33ns [*] · ars 1: +0.122ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.222ns [*] · ars 5: +0.275ns [*] - Storey 9: · ars 0: -0.0787ns [*] · ars 1: +0.168ns [*] · ars 2: +0.221ns [*] · ars 3: -0.0658ns [*] · ars 4: -1.04ns [*] · ars 5: -0.741ns [*] - Storey 10: · ars 0: +0.0979ns [*] · ars 1: +0.844ns [*] · ars 2: -0.337ns [*] · ars 3: +0.149ns [*] · ars 4: -0.583ns [*] · ars 5: -0.224ns [*] > Section #2: Calibrating from St11 to St16 using OB 1159 (L05 S09) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -8.94 slope = 0.0977 (parabola = 0.000183) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: -0.335ns [*] · ars 1: -0.5ns [*] · ars 2: -0.153ns [*] · ars 3: -0.273ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 12: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.0505ns [*] · ars 3: -0.0418ns [*] · ars 4: +0.669ns [*] · ars 5: +0.699ns [*] - Storey 13: · ars 0: -0.114ns [*] · ars 1: -0.0423ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.148ns [*] · ars 5: -0.118ns [*] - Storey 14: · ars 0: +0.163ns [*] · ars 1: -0.136ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.0263ns [*] · ars 5: -0.0305ns [*] - Storey 15: · ars 0: +0.431ns [*] · ars 1: +0.577ns [*] · ars 2: +0.305ns [*] · ars 3: +0.26ns [*] · ars 4: -0.13ns [*] · ars 5: +0.0398ns [*] - Storey 16: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available > Section #3: Calibrating from St17 to St22 using OB 1163 (L05 S15) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -3.23 slope = 0.0443 (parabola = -2.28e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.268ns [*] · ars 1: -0.0693ns [*] · ars 2: -0.318ns [*] · ars 3: -0.326ns [*] · ars 4: +0.437ns [*] · ars 5: +0.215ns [ ] - Storey 18: · ars 0: +0.142ns [*] · ars 1: +0.055ns [*] · ars 2: -0.0053ns [*] · ars 3: +0.223ns [*] · ars 4: +0.102ns [*] · ars 5: +0.0166ns [*] - Storey 19: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.106ns [*] · ars 3: -0.439ns [*] · ars 4: +0.071ns [*] · ars 5: -0.174ns [*] - Storey 20: · ars 0: +0.000612ns [*] · ars 1: +0.16ns [*] · ars 2: -0.718ns [*] · ars 3: -0.42ns [*] · ars 4: +0.316ns [*] · ars 5: +0.458ns [*] - Storey 21: · ars 0: +0.509ns [*] · ars 1: +0.373ns [*] · ars 2: -0.06ns [*] · ars 3: +0.227ns [*] · ars 4: -0.176ns [*] · ars 5: -0.469ns [*] - Storey 22: · ars 0: -0.321ns [*] · ars 1: -0.218ns [*] · ars 2: +0.176ns [*] · ars 3: +0.14ns [*] · ars 4: Not Available · ars 5: Not Available > Section #4: Calibrating from St23 to St25 using OB 1158 (L05 S21) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -20.5 slope = 0.567 (parabola = 0.024) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: -0.0766ns [*] · ars 1: -0.00928ns [*] · ars 2: +0.432ns [*] · ars 3: +0.331ns [*] · ars 4: -0.241ns [*] · ars 5: -0.436ns [*] - Storey 24: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: +5.31ns [ ] · ars 5: +5.07ns [ ] - Storey 25: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.0247ns [*] · ars 3: +0.0247ns [*] · ars 4: Not Available · ars 5: Not Available >========================================================================================< >>> Calibrating Line 6: > Section #0: Calibrating from St01 to St03 using OB 1091 (L04 S02) > Reading TTree... > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1092 (L06 S02) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -1.88 slope = 0.0758 (parabola = 0.000129) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: +0.394ns [*] · ars 1: +0.323ns [*] · ars 2: +0.637ns [*] · ars 3: +0.812ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 5: · ars 0: Not Available · ars 1: Not Available · ars 2: -1.54ns [*] · ars 3: -1.58ns [*] · ars 4: -1.32ns [*] · ars 5: -1.71ns [*] - Storey 6: · ars 0: +0.351ns [*] · ars 1: +0.423ns [*] · ars 2: +0.653ns [*] · ars 3: +0.656ns [*] · ars 4: +0.468ns [*] · ars 5: +0.406ns [*] - Storey 7: · ars 0: +0.0273ns [*] · ars 1: -0.0159ns [*] · ars 2: +0.136ns [*] · ars 3: +0.16ns [*] · ars 4: +0.594ns [*] · ars 5: +0.545ns [*] - Storey 8: · ars 0: -0.018ns [*] · ars 1: +0.0531ns [*] · ars 2: +0.229ns [*] · ars 3: -0.0181ns [*] · ars 4: +0.249ns [*] · ars 5: +0.403ns [*] - Storey 9: · ars 0: +0.0249ns [*] · ars 1: -0.143ns [*] · ars 2: +0.399ns [*] · ars 3: +0.509ns [*] · ars 4: -0.544ns [*] · ars 5: -0.464ns [*] - Storey 10: · ars 0: -0.0653ns [*] · ars 1: +0.0904ns [*] · ars 2: -0.488ns [*] · ars 3: -0.488ns [*] · ars 4: +0.202ns [*] · ars 5: -0.352ns [*] > Section #2: Calibrating from St11 to St16 using OB 1186 (L06 S09) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -4.54 slope = 0.0786 (parabola = 8.97e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: -0.0339ns [*] · ars 1: +0.114ns [*] · ars 2: -0.278ns [*] · ars 3: +0.0295ns [*] · ars 4: +0.082ns [*] · ars 5: +0.0382ns [*] - Storey 12: · ars 0: +0.0317ns [*] · ars 1: +0.173ns [*] · ars 2: -0.175ns [*] · ars 3: -0.152ns [*] · ars 4: -0.205ns [*] · ars 5: -0.00652ns [*] - Storey 13: · ars 0: +0.706ns [*] · ars 1: +0.522ns [*] · ars 2: +18.8ns [ ] · ars 3: +19ns [ ] · ars 4: -0.53ns [*] · ars 5: -0.774ns [*] - Storey 14: · ars 0: -0.0354ns [*] · ars 1: +0.00478ns [*] · ars 2: +0.576ns [*] · ars 3: +0.0738ns [*] · ars 4: -0.456ns [*] · ars 5: -0.58ns [*] - Storey 15: · ars 0: +0.0722ns [*] · ars 1: +0.567ns [*] · ars 2: +0.334ns [*] · ars 3: +0.388ns [*] · ars 4: +5.01ns [ ] · ars 5: -66.2ns [ ] - Storey 16: · ars 0: +0.318ns [*] · ars 1: +0.713ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.133ns [*] · ars 5: -0.117ns [*] > Section #3: Calibrating from St17 to St22 using OB 1046 (L06 S15) > Reading TTree... > Fitting for time corrections... -> Fit: offset = 2.02 slope = 0.0692 (parabola = -0.000172) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.236ns [*] · ars 1: +0.117ns [*] · ars 2: +0.197ns [ ] · ars 3: -0.0772ns [*] · ars 4: -0.0679ns [*] · ars 5: -0.0908ns [*] - Storey 18: · ars 0: +0.306ns [*] · ars 1: +0.2ns [*] · ars 2: -0.000106ns [*] · ars 3: -0.00642ns [*] · ars 4: -0.0369ns [*] · ars 5: +0.205ns [*] - Storey 19: · ars 0: +0.315ns [*] · ars 1: +0.403ns [*] · ars 2: -0.00615ns [*] · ars 3: +0.0524ns [*] · ars 4: -0.113ns [*] · ars 5: -0.21ns [*] - Storey 20: · ars 0: -0.364ns [*] · ars 1: -0.00388ns [*] · ars 2: -0.329ns [*] · ars 3: +0.184ns [*] · ars 4: -0.0159ns [*] · ars 5: -0.0997ns [*] - Storey 21: · ars 0: -0.124ns [*] · ars 1: -0.217ns [*] · ars 2: -0.336ns [*] · ars 3: +0.0438ns [*] · ars 4: +0.0406ns [*] · ars 5: +0.0302ns [*] - Storey 22: · ars 0: -0.3ns [*] · ars 1: -0.622ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.874ns [*] · ars 5: -1ns [*] > Section #4: Calibrating from St23 to St25 using OB 1056 (L06 S21) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -7.42 slope = 0.191 (parabola = -0.000736) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: -0.00493ns [*] · ars 1: +0.133ns [*] · ars 2: -0.0501ns [*] · ars 3: -0.0751ns [*] · ars 4: +0.145ns [*] · ars 5: +0.107ns [*] - Storey 24: · ars 0: -0.0473ns [*] · ars 1: -0.271ns [*] · ars 2: -0.0343ns [*] · ars 3: +0.0106ns [*] · ars 4: -0.168ns [*] · ars 5: +0.0288ns [ ] - Storey 25: · ars 0: +0.0238ns [*] · ars 1: -0.126ns [*] · ars 2: +0.24ns [*] · ars 3: +0.117ns [*] · ars 4: Not Available · ars 5: Not Available >========================================================================================< >>> Calibrating Line 7: > Section #0: Calibrating from St01 to St03 using OB 1025 (L09 S02) > Reading TTree... > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1195 (L07 S02) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -6.25 slope = 0.0802 (parabola = 0.000242) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: -0.192ns [*] · ars 1: -0.467ns [ ] · ars 2: -27ns [ ] · ars 3: -32ns [ ] · ars 4: -0.507ns [*] · ars 5: -0.487ns [*] - Storey 5: · ars 0: +0.0118ns [*] · ars 1: -0.0706ns [*] · ars 2: +0.236ns [*] · ars 3: +0.0898ns [*] · ars 4: +0.0834ns [*] · ars 5: +0.0111ns [*] - Storey 6: · ars 0: -0.111ns [*] · ars 1: -0.198ns [*] · ars 2: +0.0346ns [*] · ars 3: -0.0256ns [*] · ars 4: +0.0495ns [*] · ars 5: +0.462ns [*] - Storey 7: · ars 0: -0.0396ns [*] · ars 1: +0.386ns [*] · ars 2: -0.311ns [*] · ars 3: +0.0957ns [*] · ars 4: +0.253ns [*] · ars 5: +0.181ns [*] - Storey 8: · ars 0: +0.424ns [*] · ars 1: +0.19ns [*] · ars 2: -0.0346ns [*] · ars 3: +0.281ns [*] · ars 4: +0.273ns [*] · ars 5: -0.298ns [*] - Storey 9: · ars 0: +0.757ns [*] · ars 1: +0.563ns [*] · ars 2: +0.0729ns [*] · ars 3: -0.666ns [*] · ars 4: +0.157ns [*] · ars 5: +0.216ns [*] - Storey 10: · ars 0: -0.597ns [*] · ars 1: -0.575ns [*] · ars 2: -0.543ns [*] · ars 3: -0.354ns [*] · ars 4: +0.0342ns [*] · ars 5: +0.148ns [*] > Section #2: Calibrating from St11 to St16 using OB 1116 (L07 S09) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -3.46 slope = 0.0638 (parabola = -4.71e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.105ns [*] · ars 3: +0.142ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 12: · ars 0: -0.26ns [*] · ars 1: -0.0819ns [*] · ars 2: +0.00363ns [*] · ars 3: -0.00972ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 13: · ars 0: -0.16ns [*] · ars 1: +0.0249ns [*] · ars 2: -0.159ns [*] · ars 3: +0.0888ns [*] · ars 4: -72.8ns [ ] · ars 5: -74.4ns [ ] - Storey 14: · ars 0: +0.194ns [*] · ars 1: +0.338ns [*] · ars 2: +0.0351ns [*] · ars 3: +0.00723ns [*] · ars 4: +0.438ns [*] · ars 5: +0.13ns [*] - Storey 15: · ars 0: -0.257ns [*] · ars 1: -0.177ns [*] · ars 2: -0.577ns [*] · ars 3: -0.33ns [*] · ars 4: +0.0219ns [*] · ars 5: +0.405ns [*] - Storey 16: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: -0.168ns [*] · ars 5: -0.36ns [*] > Section #3: Calibrating from St17 to St22 using OB 1042 (L07 S15) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -3.21 slope = 0.0712 (parabola = 0.000175) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.0312ns [*] · ars 3: -0.202ns [*] · ars 4: +0.264ns [*] · ars 5: +0.221ns [*] - Storey 18: · ars 0: -0.348ns [*] · ars 1: -0.264ns [*] · ars 2: -0.315ns [*] · ars 3: -0.334ns [*] · ars 4: -0.524ns [*] · ars 5: -0.206ns [*] - Storey 19: · ars 0: +0.455ns [*] · ars 1: +0.155ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.448ns [*] · ars 5: +0.6ns [*] - Storey 20: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: -0.133ns [*] · ars 5: -0.000398ns [*] - Storey 21: · ars 0: -0.411ns [*] · ars 1: +0.135ns [*] · ars 2: +0.228ns [*] · ars 3: +0.122ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 22: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.0193ns [*] · ars 3: -0.0115ns [*] · ars 4: +0.78ns [*] · ars 5: +0.898ns [*] > Section #4: Calibrating from St23 to St25 using OB 1177 (L07 S21) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -2.62 slope = 0.0239 (parabola = 0.00138) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: -0.0887ns [*] · ars 1: +0.122ns [*] · ars 2: -0.18ns [*] · ars 3: -0.354ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 24: · ars 0: +0.263ns [*] · ars 1: -0.0124ns [*] · ars 2: +0.0236ns [*] · ars 3: +0.327ns [*] · ars 4: +0.277ns [*] · ars 5: +0.125ns [*] - Storey 25: · ars 0: +0.0877ns [*] · ars 1: +0.0254ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.253ns [*] · ars 5: -0.362ns [*] >========================================================================================< >>> Calibrating Line 8: > Section #0: Calibrating from St01 to St03 using OB 1242 (L10 S02) > Reading TTree... > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1232 (L08 S02) > Reading TTree... > Fitting for time corrections... -> Fit: offset = 0.434 slope = 0.0621 (parabola = 0.000242) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: -0.276ns [*] · ars 1: -0.0325ns [*] · ars 2: -0.326ns [*] · ars 3: -0.426ns [*] · ars 4: -0.204ns [*] · ars 5: -0.123ns [*] - Storey 5: · ars 0: -0.138ns [*] · ars 1: -0.146ns [*] · ars 2: +0.183ns [*] · ars 3: +0.422ns [*] · ars 4: -0.178ns [*] · ars 5: +0.0333ns [*] - Storey 6: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.147ns [*] · ars 3: +0.0294ns [*] · ars 4: +0.319ns [*] · ars 5: +0.511ns [*] - Storey 7: · ars 0: -0.104ns [*] · ars 1: -0.141ns [*] · ars 2: -0.158ns [*] · ars 3: +0.306ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 8: · ars 0: +0.071ns [*] · ars 1: +0.236ns [*] · ars 2: +0.413ns [*] · ars 3: +0.186ns [*] · ars 4: +0.464ns [*] · ars 5: +0.483ns [*] - Storey 9: · ars 0: -0.0258ns [*] · ars 1: +0.0677ns [*] · ars 2: -0.278ns [*] · ars 3: +0.242ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 10: · ars 0: -0.415ns [*] · ars 1: -0.219ns [*] · ars 2: -0.587ns [*] · ars 3: -0.559ns [*] · ars 4: +0.0299ns [*] · ars 5: +0.193ns [*] > Section #2: Calibrating from St11 to St16 using OB 1176 (L08 S09) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -0.46 slope = 0.0481 (parabola = 0.000275) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: -0.375ns [*] · ars 1: -0.468ns [*] · ars 2: -0.258ns [ ] · ars 3: -0.396ns [*] · ars 4: -0.257ns [*] · ars 5: -0.511ns [*] - Storey 12: · ars 0: +0.379ns [*] · ars 1: +0.568ns [*] · ars 2: +0.241ns [*] · ars 3: +0.301ns [*] · ars 4: +0.0976ns [*] · ars 5: +0.0367ns [*] - Storey 13: · ars 0: -0.153ns [*] · ars 1: -0.00435ns [*] · ars 2: +0.214ns [*] · ars 3: +0.105ns [*] · ars 4: -0.161ns [*] · ars 5: -0.00954ns [*] - Storey 14: · ars 0: +0.112ns [*] · ars 1: +0.284ns [*] · ars 2: +0.325ns [*] · ars 3: +0.449ns [*] · ars 4: -53.1ns [ ] · ars 5: -4.58ns [ ] - Storey 15: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.186ns [*] · ars 3: -0.0506ns [*] · ars 4: -0.16ns [*] · ars 5: -0.143ns [*] - Storey 16: · ars 0: -0.784ns [*] · ars 1: -0.346ns [*] · ars 2: +0.499ns [*] · ars 3: +0.635ns [*] · ars 4: +0.744ns [*] · ars 5: +0.778ns [*] > Section #3: Calibrating from St17 to St22 using OB 1138 (L08 S15) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -0.95 slope = 0.0828 (parabola = -0.000114) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.544ns [*] · ars 3: +0.508ns [*] · ars 4: +0.368ns [*] · ars 5: +0.218ns [*] - Storey 18: · ars 0: -0.381ns [*] · ars 1: -0.164ns [*] · ars 2: -45.6ns [ ] · ars 3: -1ns [*] · ars 4: +0.0842ns [*] · ars 5: +0.0622ns [*] - Storey 19: · ars 0: -0.596ns [*] · ars 1: -0.149ns [*] · ars 2: +0.494ns [*] · ars 3: +0.376ns [*] · ars 4: -0.224ns [*] · ars 5: -0.564ns [*] - Storey 20: · ars 0: +0.0146ns [*] · ars 1: +0.249ns [*] · ars 2: -0.567ns [*] · ars 3: -0.47ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 21: · ars 0: +0.108ns [*] · ars 1: +0.446ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.0743ns [*] · ars 5: -0.17ns [*] - Storey 22: · ars 0: -0.225ns [*] · ars 1: +0.117ns [*] · ars 2: +0.453ns [*] · ars 3: -0.381ns [*] · ars 4: +0.931ns [*] · ars 5: +0.324ns [*] > Section #4: Calibrating from St23 to St25 using OB 1219 (L08 S21) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -3.3 slope = 0.143 (parabola = 0.000624) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: +0.0543ns [*] · ars 1: +0.0106ns [*] · ars 2: -0.372ns [*] · ars 3: -0.314ns [ ] · ars 4: -0.0261ns [*] · ars 5: +0.0793ns [*] - Storey 24: · ars 0: +0.151ns [*] · ars 1: +0.0448ns [*] · ars 2: -0.0869ns [*] · ars 3: +0.048ns [*] · ars 4: +0.169ns [*] · ars 5: +0.183ns [*] - Storey 25: · ars 0: -0.0531ns [*] · ars 1: -0.101ns [*] · ars 2: +0.0239ns [*] · ars 3: -0.237ns [*] · ars 4: +0.00824ns [*] · ars 5: +0.104ns [*] >========================================================================================< >>> Calibrating Line 9: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > Reading TTree... > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1025 (L09 S02) > Reading TTree... > Fitting for time corrections... -> Fit: offset = 3.52 slope = 0.0556 (parabola = -0.000169) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: +0.164ns [*] · ars 1: -0.0536ns [*] · ars 2: +0.068ns [*] · ars 3: +0.123ns [*] · ars 4: +0.134ns [*] · ars 5: +0.223ns [*] - Storey 5: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.55ns [*] · ars 3: +0.346ns [*] · ars 4: -0.0721ns [*] · ars 5: -0.264ns [*] - Storey 6: · ars 0: -82.7ns [ ] · ars 1: -39ns [ ] · ars 2: -3.67ns [ ] · ars 3: -3.29ns [ ] · ars 4: -0.425ns [*] · ars 5: -0.455ns [*] - Storey 7: · ars 0: +0.372ns [*] · ars 1: +0.409ns [*] · ars 2: -0.731ns [*] · ars 3: -0.64ns [*] · ars 4: -0.251ns [*] · ars 5: -0.297ns [*] - Storey 8: · ars 0: +0.0345ns [*] · ars 1: +0.35ns [*] · ars 2: +0.0948ns [*] · ars 3: -0.188ns [*] · ars 4: +0.152ns [*] · ars 5: -0.0384ns [*] - Storey 9: · ars 0: -5.75ns [ ] · ars 1: -55.4ns [ ] · ars 2: -0.371ns [*] · ars 3: -0.325ns [*] · ars 4: +0.0766ns [*] · ars 5: -0.0122ns [*] - Storey 10: · ars 0: +0.386ns [*] · ars 1: +0.175ns [*] · ars 2: +0.0293ns [*] · ars 3: +0.436ns [*] · ars 4: -3.38ns [ ] · ars 5: -4.12ns [ ] > Section #2: Calibrating from St11 to St16 using OB 1247 (L09 S09) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -2.05 slope = 0.0562 (parabola = -0.000141) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: +0.058ns [*] · ars 1: +0.482ns [*] · ars 2: -0.0502ns [*] · ars 3: +0.0119ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 12: · ars 0: -0.112ns [*] · ars 1: -0.0416ns [*] · ars 2: +0.0791ns [*] · ars 3: -0.0698ns [*] · ars 4: +0.34ns [*] · ars 5: +0.751ns [*] - Storey 13: · ars 0: -0.137ns [ ] · ars 1: -0.0296ns [*] · ars 2: -0.332ns [*] · ars 3: -0.73ns [*] · ars 4: -0.44ns [*] · ars 5: -0.468ns [*] - Storey 14: · ars 0: -2.67ns [ ] · ars 1: -2.55ns [ ] · ars 2: -0.0792ns [*] · ars 3: -0.301ns [*] · ars 4: +0.267ns [*] · ars 5: +0.00789ns [*] - Storey 15: · ars 0: +0.12ns [*] · ars 1: +0.123ns [*] · ars 2: -2.1ns [ ] · ars 3: -2.26ns [ ] · ars 4: +0.0593ns [*] · ars 5: +0.126ns [*] - Storey 16: · ars 0: +0.158ns [*] · ars 1: +0.0456ns [*] · ars 2: -0.204ns [*] · ars 3: +0.107ns [*] · ars 4: -0.241ns [*] · ars 5: -0.153ns [*] > Section #3: Calibrating from St17 to St22 using OB 1068 (L09 S15) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -4.35 slope = 0.0592 (parabola = -2.87e-06) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: -0.0135ns [*] · ars 1: +0.0805ns [*] · ars 2: -8.09ns [ ] · ars 3: -8.16ns [ ] · ars 4: +0.0963ns [*] · ars 5: +0.147ns [*] - Storey 18: · ars 0: -0.252ns [*] · ars 1: -0.223ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -24.4ns [ ] · ars 5: -25ns [ ] - Storey 19: · ars 0: -0.353ns [*] · ars 1: -0.164ns [*] · ars 2: +0.0287ns [*] · ars 3: +0.0692ns [*] · ars 4: -0.249ns [*] · ars 5: +0.132ns [*] - Storey 20: · ars 0: +0.284ns [*] · ars 1: -0.0575ns [*] · ars 2: +0.358ns [*] · ars 3: +0.403ns [*] · ars 4: -0.0157ns [*] · ars 5: +0.0668ns [*] - Storey 21: · ars 0: -0.0315ns [*] · ars 1: +0.0138ns [*] · ars 2: -0.0748ns [*] · ars 3: +0.0797ns [*] · ars 4: +0.247ns [*] · ars 5: +0.0455ns [*] - Storey 22: · ars 0: -0.318ns [*] · ars 1: -0.132ns [*] · ars 2: -2.4ns [ ] · ars 3: -2.81ns [ ] · ars 4: -0.0911ns [*] · ars 5: -0.482ns [*] > Section #4: Calibrating from St23 to St25 using OB 1263 (L09 S21) > Reading TTree... > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 10: > Section #0: Calibrating from St01 to St03 using OB 1232 (L08 S02) > Reading TTree... > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1242 (L10 S02) > Reading TTree... > Fitting for time corrections... -> Fit: offset = 0.677 slope = 0.0764 (parabola = -4.2e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: -0.0751ns [*] · ars 1: -0.245ns [*] · ars 2: +0.334ns [*] · ars 3: +0.21ns [*] · ars 4: -0.0241ns [*] · ars 5: -0.0184ns [*] - Storey 5: · ars 0: -0.272ns [*] · ars 1: +0.0804ns [*] · ars 2: +0.578ns [*] · ars 3: +0.101ns [ ] · ars 4: +0.139ns [*] · ars 5: +0.155ns [*] - Storey 6: · ars 0: -0.144ns [*] · ars 1: -0.161ns [*] · ars 2: -0.241ns [*] · ars 3: -0.0515ns [*] · ars 4: -0.503ns [*] · ars 5: -0.642ns [*] - Storey 7: · ars 0: +0.187ns [*] · ars 1: +0.357ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available - Storey 8: · ars 0: -0.283ns [*] · ars 1: -0.127ns [*] · ars 2: +0.214ns [*] · ars 3: +0.202ns [*] · ars 4: +0.527ns [*] · ars 5: +0.691ns [*] - Storey 9: · ars 0: -0.343ns [*] · ars 1: -0.272ns [*] · ars 2: +0.304ns [*] · ars 3: +0.431ns [*] · ars 4: -0.822ns [*] · ars 5: -0.895ns [*] - Storey 10: · ars 0: -0.231ns [*] · ars 1: -0.227ns [*] · ars 2: +0.174ns [*] · ars 3: +0.308ns [*] · ars 4: +0.524ns [*] · ars 5: +0.163ns [*] > Section #2: Calibrating from St11 to St16 using OB 1277 (L10 S09) > Reading TTree... > Fitting for time corrections... -> Fit: offset = 0.192 slope = 0.0683 (parabola = -0.000129) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: +0.0203ns [*] · ars 1: -0.259ns [*] · ars 2: +0.0641ns [*] · ars 3: +0.198ns [ ] · ars 4: -0.0558ns [*] · ars 5: -0.112ns [*] - Storey 12: · ars 0: +0.293ns [*] · ars 1: +0.401ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.403ns [*] · ars 5: +0.305ns [*] - Storey 13: · ars 0: -0.0558ns [*] · ars 1: +0.208ns [*] · ars 2: -0.0406ns [*] · ars 3: +0.239ns [*] · ars 4: -0.335ns [*] · ars 5: -0.122ns [*] - Storey 14: · ars 0: +0.618ns [*] · ars 1: +0.202ns [*] · ars 2: +0.321ns [*] · ars 3: +0.266ns [*] · ars 4: -0.84ns [*] · ars 5: -0.248ns [*] - Storey 15: · ars 0: -0.257ns [*] · ars 1: -0.398ns [*] · ars 2: -0.762ns [*] · ars 3: -0.524ns [*] · ars 4: -0.38ns [*] · ars 5: -0.408ns [*] - Storey 16: · ars 0: -0.324ns [*] · ars 1: +0.306ns [*] · ars 2: -0.127ns [*] · ars 3: +0.127ns [*] · ars 4: -5.21ns [ ] · ars 5: -4.09ns [ ] > Section #3: Calibrating from St17 to St22 using OB 1249 (L10 S15) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -2.69 slope = 0.106 (parabola = 5.15e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.163ns [*] · ars 1: +0.0748ns [*] · ars 2: -0.171ns [*] · ars 3: -0.191ns [*] · ars 4: -0.321ns [*] · ars 5: -0.279ns [*] - Storey 18: · ars 0: +0.0183ns [*] · ars 1: -0.216ns [*] · ars 2: -0.335ns [*] · ars 3: -0.208ns [*] · ars 4: -0.103ns [*] · ars 5: +0.269ns [*] - Storey 19: · ars 0: +0.367ns [*] · ars 1: +0.693ns [*] · ars 2: +0.253ns [*] · ars 3: +0.089ns [*] · ars 4: +0.325ns [*] · ars 5: +0.654ns [*] - Storey 20: · ars 0: +0.651ns [*] · ars 1: -0.00787ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.245ns [*] · ars 5: +0.33ns [*] - Storey 21: · ars 0: -0.325ns [*] · ars 1: -0.558ns [*] · ars 2: -0.888ns [*] · ars 3: -0.436ns [*] · ars 4: -0.463ns [*] · ars 5: -0.497ns [*] - Storey 22: · ars 0: +0.0114ns [*] · ars 1: +0.315ns [*] · ars 2: -0.207ns [*] · ars 3: -0.421ns [*] · ars 4: +0.0878ns [*] · ars 5: +0.584ns [*] > Section #4: Calibrating from St23 to St25 using OB 1224 (L10 S21) > Reading TTree... > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 11: > Section #0: Calibrating from St01 to St03 using OB 1088 (L12 S02) > Reading TTree... > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1236 (L11 S02) > Reading TTree... > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #2: Calibrating from St11 to St16 using OB 1309 (L11 S09) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -5.07 slope = 0.0725 (parabola = 0.00029) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.212ns [*] · ars 3: -0.0329ns [*] · ars 4: -88.5ns [ ] · ars 5: -100ns [ ] - Storey 12: · ars 0: -0.42ns [*] · ars 1: -0.395ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.562ns [*] · ars 5: -0.581ns [*] - Storey 13: · ars 0: +0.876ns [*] · ars 1: +0.975ns [*] · ars 2: +0.449ns [*] · ars 3: +0.254ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 14: · ars 0: +0.303ns [*] · ars 1: -0.0627ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available - Storey 15: · ars 0: -0.23ns [*] · ars 1: -0.123ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available - Storey 16: · ars 0: +0.142ns [*] · ars 1: -0.0583ns [*] · ars 2: -0.217ns [*] · ars 3: +0.475ns [*] · ars 4: +0.348ns [*] · ars 5: +0.337ns [*] > Section #3: Calibrating from St17 to St22 using OB 1272 (L11 S15) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -4.62 slope = 0.074 (parabola = -0.000263) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.143ns [*] · ars 1: -0.000111ns [*] · ars 2: +0.0384ns [*] · ars 3: +0.256ns [*] · ars 4: +0.294ns [*] · ars 5: +0.403ns [*] - Storey 18: · ars 0: -0.0771ns [*] · ars 1: -0.0208ns [*] · ars 2: -0.318ns [*] · ars 3: -0.011ns [*] · ars 4: -0.0569ns [*] · ars 5: -0.0901ns [*] - Storey 19: · ars 0: -0.0746ns [*] · ars 1: +0.226ns [*] · ars 2: -0.276ns [*] · ars 3: +0.0274ns [*] · ars 4: -0.0529ns [*] · ars 5: -0.131ns [*] - Storey 20: · ars 0: -2.2ns [ ] · ars 1: -2.12ns [ ] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.238ns [*] · ars 5: -0.407ns [*] - Storey 21: · ars 0: +0.0274ns [*] · ars 1: +0.232ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available - Storey 22: · ars 0: -0.116ns [*] · ars 1: -0.718ns [*] · ars 2: -0.107ns [*] · ars 3: -0.178ns [*] · ars 4: -0.178ns [*] · ars 5: -0.102ns [*] > Section #4: Calibrating from St23 to St25 using OB 1274 (L11 S21) > Reading TTree... > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 12: > Section #0: Calibrating from St01 to St03 using OB 1236 (L11 S02) > Reading TTree... > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1088 (L12 S02) > Reading TTree... > Fitting for time corrections... -> Fit: offset = 2.41 slope = 0.087 (parabola = -0.000128) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: +0.141ns [*] · ars 1: +0.692ns [*] · ars 2: +0.14ns [*] · ars 3: +0.175ns [*] · ars 4: -0.0291ns [*] · ars 5: -0.189ns [*] - Storey 5: · ars 0: -0.178ns [*] · ars 1: -0.275ns [*] · ars 2: -0.551ns [*] · ars 3: -0.307ns [*] · ars 4: -0.0431ns [*] · ars 5: +0.198ns [*] - Storey 6: · ars 0: -0.00187ns [*] · ars 1: +0.0343ns [*] · ars 2: +0.304ns [*] · ars 3: +0.0895ns [*] · ars 4: -0.074ns [*] · ars 5: +0.039ns [*] - Storey 7: · ars 0: -0.156ns [*] · ars 1: +0.196ns [*] · ars 2: +0.187ns [*] · ars 3: +0.165ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 8: · ars 0: +0.0768ns [*] · ars 1: +0.461ns [*] · ars 2: -0.619ns [*] · ars 3: -0.467ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 9: · ars 0: -1.15ns [*] · ars 1: -1.17ns [*] · ars 2: +0.171ns [*] · ars 3: +0.0126ns [*] · ars 4: +0.251ns [*] · ars 5: +0.437ns [*] - Storey 10: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.122ns [*] · ars 3: -0.0393ns [*] · ars 4: +0.652ns [*] · ars 5: +0.705ns [*] > Section #2: Calibrating from St11 to St16 using OB 1038 (L12 S09) > Reading TTree... > Fitting for time corrections... -> Fit: offset = -0.45 slope = 0.0757 (parabola = 7.2e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: +0.121ns [*] · ars 1: +0.14ns [*] · ars 2: +0.261ns [*] · ars 3: +0.391ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 12: · ars 0: -47.1ns [ ] · ars 1: -0.622ns [*] · ars 2: -1ns [*] · ars 3: -46.6ns [ ] · ars 4: -0.207ns [*] · ars 5: -0.0231ns [*] - Storey 13: · ars 0: +0.0564ns [*] · ars 1: +0.138ns [*] · ars 2: +0.158ns [*] · ars 3: +0.236ns [*] · ars 4: -0.26ns [*] · ars 5: -0.346ns [*] - Storey 14: · ars 0: +0.148ns [*] · ars 1: +0.145ns [*] · ars 2: -0.46ns [*] · ars 3: -0.421ns [*] · ars 4: +0.348ns [*] · ars 5: +0.662ns [*] - Storey 15: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.108ns [*] · ars 3: -0.327ns [*] · ars 4: +0.352ns [*] · ars 5: +0.506ns [*] - Storey 16: · ars 0: -0.325ns [*] · ars 1: -0.309ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.985ns [*] · ars 5: +1.39ns [*] > Section #3: Calibrating from St17 to St22 using OB 1041 (L12 S15) > Reading TTree... > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #4: Calibrating from St23 to St25 using OB 1294 (L12 S21) > Reading TTree... > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >> Report of all ERRORs: >========================================================================================< >>> Calibrating Line 1: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1631 (L01 S02) > Section #2: Calibrating from St11 to St16 using OB 1643 (L01 S09) > Section #3: Calibrating from St17 to St22 using OB 1628 (L01 S15) > Section #4: Calibrating from St23 to St25 using OB 1621 (L01 S21) >========================================================================================< >>> Calibrating Line 2: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1095 (L02 S02) > Section #2: Calibrating from St11 to St16 using OB 1048 (L02 S09) > Section #3: Calibrating from St17 to St22 using OB 1065 (L02 S15) > Section #4: Calibrating from St23 to St25 using OB 1118 (L02 S21) >========================================================================================< >>> Calibrating Line 3: > Section #0: Calibrating from St01 to St03 using OB 1193 (L05 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1027 (L03 S02) > Section #2: Calibrating from St11 to St16 using OB 1157 (L03 S09) > Section #3: Calibrating from St17 to St22 using OB 1140 (L03 S15) > Section #4: Calibrating from St23 to St25 using OB 1106 (L03 S21) >========================================================================================< >>> Calibrating Line 4: > Section #0: Calibrating from St01 to St03 using OB 1092 (L06 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1091 (L04 S02) > Section #2: Calibrating from St11 to St16 using OB 1141 (L04 S09) > Section #3: Calibrating from St17 to St22 using OB 1115 (L04 S15) > Section #4: Calibrating from St23 to St25 using OB 1151 (L04 S21) >========================================================================================< >>> Calibrating Line 5: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1193 (L05 S02) > Section #2: Calibrating from St11 to St16 using OB 1159 (L05 S09) > Section #3: Calibrating from St17 to St22 using OB 1163 (L05 S15) > Section #4: Calibrating from St23 to St25 using OB 1158 (L05 S21) >========================================================================================< >>> Calibrating Line 6: > Section #0: Calibrating from St01 to St03 using OB 1091 (L04 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1092 (L06 S02) > Section #2: Calibrating from St11 to St16 using OB 1186 (L06 S09) > Section #3: Calibrating from St17 to St22 using OB 1046 (L06 S15) > Section #4: Calibrating from St23 to St25 using OB 1056 (L06 S21) >========================================================================================< >>> Calibrating Line 7: > Section #0: Calibrating from St01 to St03 using OB 1025 (L09 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1195 (L07 S02) > Section #2: Calibrating from St11 to St16 using OB 1116 (L07 S09) > Section #3: Calibrating from St17 to St22 using OB 1042 (L07 S15) > Section #4: Calibrating from St23 to St25 using OB 1177 (L07 S21) >========================================================================================< >>> Calibrating Line 8: > Section #0: Calibrating from St01 to St03 using OB 1242 (L10 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1232 (L08 S02) > Section #2: Calibrating from St11 to St16 using OB 1176 (L08 S09) > Section #3: Calibrating from St17 to St22 using OB 1138 (L08 S15) > Section #4: Calibrating from St23 to St25 using OB 1219 (L08 S21) >========================================================================================< >>> Calibrating Line 9: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1025 (L09 S02) > Section #2: Calibrating from St11 to St16 using OB 1247 (L09 S09) > Section #3: Calibrating from St17 to St22 using OB 1068 (L09 S15) > Section #4: Calibrating from St23 to St25 using OB 1263 (L09 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 10: > Section #0: Calibrating from St01 to St03 using OB 1232 (L08 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1242 (L10 S02) > Section #2: Calibrating from St11 to St16 using OB 1277 (L10 S09) > Section #3: Calibrating from St17 to St22 using OB 1249 (L10 S15) > Section #4: Calibrating from St23 to St25 using OB 1224 (L10 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 11: > Section #0: Calibrating from St01 to St03 using OB 1088 (L12 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1236 (L11 S02) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #2: Calibrating from St11 to St16 using OB 1309 (L11 S09) > Section #3: Calibrating from St17 to St22 using OB 1272 (L11 S15) > Section #4: Calibrating from St23 to St25 using OB 1274 (L11 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 12: > Section #0: Calibrating from St01 to St03 using OB 1236 (L11 S02) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1088 (L12 S02) > Section #2: Calibrating from St11 to St16 using OB 1038 (L12 S09) > Section #3: Calibrating from St17 to St22 using OB 1041 (L12 S15) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #4: Calibrating from St23 to St25 using OB 1294 (L12 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Finished! /////////////////////////////////////////////////////////////////////////////////////////////////////////// # LED Runes para la calibración intraline intermedia (#10D) -> START: 30/07/2012 # @runes = ("65847" ,"65846" ,"65845" ,"65844" ,"65843" ,"65842" ,"65840" ,"65839" ,"65838" ,"65837" ,"65836" ,"65835" ,"65834" ,"65833" ,"65832" ,"65831" ,"65830" ,"65829" ,"65828" ,"65827" ,"65826" ,"65825" ,"65824" ,"65822" ); # @date = ( 120730 ); # $runcal = "2012:V1.0";