Friday, January 20 2012 intratical_10 calibration new T0 set after HV tuning Dec11 New T0 set after HV tuning in December 2011. Used T0s of after HV tuning in Jun10 (OID 65091301) and runes of 16/01/2012. Log available at: "http://ific.uv.es/~agusanlo/calibrations/intratical_10" /////////////////////////////////////////////////////////////////////////////////////////////////////////// Intraline calibration performed with standard LED-OB calibration runes of 16/01/2012: online calibration "2011:V4.0" with rigid alignment: > LABEL = "2011:V4.0" ( VERSION_ID = 66225727 ) (<- Interline offsets not included) > ARS_T0_VERSION = 65091301 > ARS_TVC_VERSION = 57889518 > ARS_AVC_0PE_VERSION = 66225718 > ARS_AVC_1PE_VERSION = 66225725 > ALIGNMENT_VERSION = 59100183 > ARS_XT_VERSION = 66225726 walk correction disabled (old style), no more corrections (cross talk, etc) in consideration taken (old style) Section #0 1-3 (Not performed) Section #1 4-10 Section #2 11-16(17) Section #3 17-22(23) Section #4 23-25 Also these LED OBs were not available: L9F21 L10F21 L11S02 L11S21 L12S15 Clockphases: > old runTimeStamp = 1309325600 (Wed, 29 Jun 2011 05:33:20 +0000 (GMT) + 0 nsec) > old CLOCK_RUN_ID = 163345 > old CLOCK_CONFIGURATION_ID = 275 > new runTimeStamp = 1326672000 (Mon, 16 Jan 2012 00:00:00 +0000 (GMT) + 0 nsec) > new CLOCK_RUN_ID = 164426 > new CLOCK_CONFIGURATION_ID = 275 Those new clockphases were used for the new T0s table: > new CLOCK_RUN_ID = 164426 > new CLOCK_CONFIGURATION_ID = 275 As in observations is mentioned, because of particularities of the L09S21 LED-OB a sector couldn't be calibrated. > Histogram Statistics T0s: > Minimum difference: -7.03111 > Maximum difference: 31.41 > Histogram Statistics CLKs: > Minimum difference: -0.053 > Maximum difference: 0.05 > Histogram Statistics T0s+CLKs: > Minimum difference: -7.01411 > Maximum difference: 31.399 new T0 ID 94617161 /////////////////////////////////////////////////////////////////////////////////////////////////////////// Observations during revision of the autobinning-intratical output: - L9 Section#4 (OB L09S21) time window was lost after a Led OB's T0's correction of -75ns and a runsetup error: -> Only for practical reasons was useful to correct it -75 ns, but that was useless (¿It should have been +75 ns?) -> Between 1st and 7th of February the LED OB started to work oddly and is not suitable for time calibration any longer. -> LED OB 1263 L09S21 lost for calibration -> The used runsetups had EN_ADQ for that LED OB OFF, excepting for the L6F2 runsetup, but no signal there for it either. -> The T0 will be reversed also should not be related with that. - List of some weird signals corrected: · L09 S09 ARS0 (Big correction of -6ns) · L09 S09 ARS1 (Big correction of -6ns) · L04 S10 ARS2 · L06 S13 ARS2 (Big correction of -31ns) · L06 S13 ARS3 (Big correction of -31ns) · L06 S15 ARS4 (Big correction of -7ns) · L06 S15 ARS5 (Big correction of -7ns) · L10 S05 ARS3 (Big Token Ring Peak) · L12 S04 ARS0 (No Token Ring Peak) · L12 S04 ARS1 (No Token Ring Peak) - List of ARS corrected by hand: · L03 S15 ARS2 · L03 S15 ARS3 · L04 S11 ARS1 · L04 S17 ARS4 · L04 S17 ARS5 · L08 S23 ARS0 · L11 S17 ARS3 - List of ARS that were decided not to be corrected (0ns of correction): · L02 S10 ars2 · L02 S10 ars3 · L03 S14 ars2 · L03 S14 ars3 · L05 S24 ars4 (Unbalanced section) · L05 S24 ars5 (Unbalanced section) · L07 S13 ars4 · L07 S13 ars5 · L11 S11 ars4 (signals reported also in attached pictures) /////////////////////////////////////////////////////////////////////////////////////////////////////////// Calibration_manager Statistics after the human inspection: > Statistics: (1770 ARS) - 240 with no run (i.e. no OB) available to perform calibration. [0ns APPLIED] (LED OBs not used: L09S21 L10S21 L11S02 L11S21 L12S15 ) - 274 which their histograms don't exist. [0ns APPLIED] - 2 are an official Dead Channel not among the listed before. [0ns APPLIED] - 1185 are ready to be corrected without problems. - 20 are a pair of ARSs miscalibrated more than 1ns. [20 REVISED (100%) / 0 TOUCHÉ REMAINS] - 11 have a bad performed fit but lie in the fit zone. [11 APPLIED (100%)] - 46 lie out of the exclusion zone with a good fit performed. [46 APPLIED (100%)] - 12 lie out of the exclusion zone with a bad fit performed. [12 APPLIED (100%)] All counted sum a total of 1770 ARSs. - 0 should still be revised + 0 perfect ARS pairs. At The End: - 516 couldn't be corrected. (no data or dead channel) - 9 were decided not to be corrected. (0ns of correction) - 1245 were decided to be corrected: · 1094 less than 1ns. · 105 between 1ns and 2ns. · 38 between 2ns and 5ns. · 8 more than 5ns. - And 20 are in a pair corrected more than 1ns: · 14 less than 2ns. · 6 between 2ns and 5ns. · 0 more than 5ns. /////////////////////////////////////////////////////////////////////////////////////////////////////////// ARS that couldn't be corrected (no data or Dead Channel): L01 S01 ars0; L01 S01 ars1; L01 S01 ars2; L01 S01 ars3; L01 S01 ars4; L01 S01 ars5; L01 S02 ars0; L01 S02 ars1; L01 S02 ars2; L01 S02 ars3; L01 S02 ars4; L01 S02 ars5; L01 S03 ars0; L01 S03 ars1; L01 S03 ars2; L01 S03 ars3; L01 S03 ars4; L01 S03 ars5; L01 S04 ars0; L01 S04 ars1; ; ; ; ; ; ; L01 S05 ars2; L01 S05 ars3; ; ; ; ; ; ; ; ; L01 S07 ars0; L01 S07 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L01 S11 ars2; L01 S11 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L01 S14 ars0; L01 S14 ars1; ; ; ; ; ; ; L01 S15 ars2; L01 S15 ars3; ; ; ; ; ; ; L01 S16 ars4; L01 S16 ars5; ; ; ; ; ; ; ; ; L01 S18 ars2; L01 S18 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L01 S22 ars2; L01 S22 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L02 S01 ars0; L02 S01 ars1; L02 S01 ars2; L02 S01 ars3; L02 S01 ars4; L02 S01 ars5; L02 S02 ars0; L02 S02 ars1; L02 S02 ars2; L02 S02 ars3; L02 S02 ars4; L02 S02 ars5; L02 S03 ars0; L02 S03 ars1; L02 S03 ars2; L02 S03 ars3; L02 S03 ars4; L02 S03 ars5; L02 S04 ars0; L02 S04 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L02 S07 ars0; L02 S07 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L02 S10 ars0; L02 S10 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L02 S22 ars0; L02 S22 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L03 S01 ars0; L03 S01 ars1; L03 S01 ars2; L03 S01 ars3; L03 S01 ars4; L03 S01 ars5; L03 S02 ars0; L03 S02 ars1; L03 S02 ars2; L03 S02 ars3; L03 S02 ars4; L03 S02 ars5; L03 S03 ars0; L03 S03 ars1; L03 S03 ars2; L03 S03 ars3; L03 S03 ars4; L03 S03 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L03 S09 ars2; L03 S09 ars3; ; ; ; ; ; ; ; ; L03 S11 ars0; L03 S11 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L03 S17 ars2; L03 S17 ars3; ; ; ; ; ; ; L03 S18 ars4; L03 S18 ars5; ; ; ; ; L03 S19 ars4; L03 S19 ars5; ; ; ; ; ; ; ; ; L03 S21 ars2; L03 S21 ars3; ; ; ; ; ; ; L03 S22 ars4; L03 S22 ars5; ; ; ; ; ; ; ; ; ; ; ; ; L03 S25 ars0; L03 S25 ars1; ; ; ; ; L04 S01 ars0; L04 S01 ars1; L04 S01 ars2; L04 S01 ars3; L04 S01 ars4; L04 S01 ars5; L04 S02 ars0; L04 S02 ars1; L04 S02 ars2; L04 S02 ars3; L04 S02 ars4; L04 S02 ars5; L04 S03 ars0; L04 S03 ars1; L04 S03 ars2; L04 S03 ars3; L04 S03 ars4; L04 S03 ars5; ; ; L04 S04 ars2; L04 S04 ars3; ; ; ; ; ; ; L04 S05 ars4; L04 S05 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L04 S12 ars0; L04 S12 ars1; L04 S12 ars2; L04 S12 ars3; L04 S12 ars4; L04 S12 ars5; ; ; ; ; ; ; ; ; L04 S14 ars2; L04 S14 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L05 S01 ars0; L05 S01 ars1; L05 S01 ars2; L05 S01 ars3; L05 S01 ars4; L05 S01 ars5; L05 S02 ars0; L05 S02 ars1; L05 S02 ars2; L05 S02 ars3; L05 S02 ars4; L05 S02 ars5; L05 S03 ars0; L05 S03 ars1; L05 S03 ars2; L05 S03 ars3; L05 S03 ars4; L05 S03 ars5; ; ; ; ; ; ; ; ; ; ; L05 S05 ars4; L05 S05 ars5; ; ; ; ; ; ; L05 S07 ars0; L05 S07 ars1; ; ; ; ; ; ; L05 S08 ars2; L05 S08 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L05 S11 ars4; L05 S11 ars5; L05 S12 ars0; L05 S12 ars1; ; ; ; ; ; ; L05 S13 ars2; L05 S13 ars3; ; ; ; ; L05 S14 ars2; L05 S14 ars3; ; ; ; ; ; ; ; ; L05 S16 ars0; L05 S16 ars1; L05 S16 ars2; L05 S16 ars3; L05 S16 ars4; L05 S16 ars5; ; ; ; ; ; ; ; ; ; ; ; ; L05 S19 ars0; L05 S19 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L05 S22 ars4; L05 S22 ars5; ; ; ; ; ; ; L05 S24 ars0; L05 S24 ars1; L05 S24 ars2; L05 S24 ars3; ; ; L05 S25 ars0; L05 S25 ars1; ; ; L05 S25 ars4; L05 S25 ars5; L06 S01 ars0; L06 S01 ars1; L06 S01 ars2; L06 S01 ars3; L06 S01 ars4; L06 S01 ars5; L06 S02 ars0; L06 S02 ars1; L06 S02 ars2; L06 S02 ars3; L06 S02 ars4; L06 S02 ars5; L06 S03 ars0; L06 S03 ars1; L06 S03 ars2; L06 S03 ars3; L06 S03 ars4; L06 S03 ars5; ; ; ; ; L06 S04 ars4; L06 S04 ars5; L06 S05 ars0; L06 S05 ars1; L06 S05 ars2; L06 S05 ars3; L06 S05 ars4; L06 S05 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L06 S22 ars2; L06 S22 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L06 S25 ars4; L06 S25 ars5; L07 S01 ars0; L07 S01 ars1; L07 S01 ars2; L07 S01 ars3; L07 S01 ars4; L07 S01 ars5; L07 S02 ars0; L07 S02 ars1; L07 S02 ars2; L07 S02 ars3; L07 S02 ars4; L07 S02 ars5; L07 S03 ars0; L07 S03 ars1; L07 S03 ars2; L07 S03 ars3; L07 S03 ars4; L07 S03 ars5; ; ; L07 S04 ars2; L07 S04 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L07 S11 ars0; L07 S11 ars1; ; ; L07 S11 ars4; L07 S11 ars5; ; ; ; ; L07 S12 ars4; L07 S12 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L07 S16 ars0; L07 S16 ars1; L07 S16 ars2; L07 S16 ars3; ; ; L07 S17 ars0; L07 S17 ars1; ; ; ; ; ; ; ; ; ; ; ; ; L07 S19 ars2; L07 S19 ars3; ; ; L07 S20 ars0; L07 S20 ars1; L07 S20 ars2; L07 S20 ars3; ; ; ; ; ; ; L07 S21 ars4; L07 S21 ars5; L07 S22 ars0; L07 S22 ars1; ; ; ; ; ; ; ; ; L07 S23 ars4; L07 S23 ars5; ; ; ; ; ; ; ; ; L07 S25 ars2; L07 S25 ars3; ; ; L08 S01 ars0; L08 S01 ars1; L08 S01 ars2; L08 S01 ars3; L08 S01 ars4; L08 S01 ars5; L08 S02 ars0; L08 S02 ars1; L08 S02 ars2; L08 S02 ars3; L08 S02 ars4; L08 S02 ars5; L08 S03 ars0; L08 S03 ars1; L08 S03 ars2; L08 S03 ars3; L08 S03 ars4; L08 S03 ars5; ; ; ; ; ; ; ; ; ; ; ; ; L08 S06 ars0; L08 S06 ars1; ; ; ; ; ; ; ; ; L08 S07 ars4; L08 S07 ars5; ; ; ; ; ; ; ; ; ; ; L08 S09 ars4; L08 S09 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L08 S15 ars0; L08 S15 ars1; ; ; ; ; ; ; ; ; ; ; L08 S17 ars0; L08 S17 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L08 S20 ars4; L08 S20 ars5; ; ; L08 S21 ars2; L08 S21 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L09 S01 ars0; L09 S01 ars1; L09 S01 ars2; L09 S01 ars3; L09 S01 ars4; L09 S01 ars5; L09 S02 ars0; L09 S02 ars1; L09 S02 ars2; L09 S02 ars3; L09 S02 ars4; L09 S02 ars5; L09 S03 ars0; L09 S03 ars1; L09 S03 ars2; L09 S03 ars3; L09 S03 ars4; L09 S03 ars5; ; ; ; ; ; ; L09 S05 ars0; L09 S05 ars1; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L09 S18 ars2; L09 S18 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L09 S23 ars0; L09 S23 ars1; L09 S23 ars2; L09 S23 ars3; L09 S23 ars4; L09 S23 ars5; L09 S24 ars0; L09 S24 ars1; L09 S24 ars2; L09 S24 ars3; L09 S24 ars4; L09 S24 ars5; L09 S25 ars0; L09 S25 ars1; L09 S25 ars2; L09 S25 ars3; L09 S25 ars4; L09 S25 ars5; L10 S01 ars0; L10 S01 ars1; L10 S01 ars2; L10 S01 ars3; L10 S01 ars4; L10 S01 ars5; L10 S02 ars0; L10 S02 ars1; L10 S02 ars2; L10 S02 ars3; L10 S02 ars4; L10 S02 ars5; L10 S03 ars0; L10 S03 ars1; L10 S03 ars2; L10 S03 ars3; L10 S03 ars4; L10 S03 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L10 S07 ars2; L10 S07 ars3; L10 S07 ars4; L10 S07 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L10 S12 ars2; L10 S12 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L10 S20 ars2; L10 S20 ars3; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L10 S23 ars0; L10 S23 ars1; L10 S23 ars2; L10 S23 ars3; L10 S23 ars4; L10 S23 ars5; L10 S24 ars0; L10 S24 ars1; L10 S24 ars2; L10 S24 ars3; L10 S24 ars4; L10 S24 ars5; L10 S25 ars0; L10 S25 ars1; L10 S25 ars2; L10 S25 ars3; L10 S25 ars4; L10 S25 ars5; L11 S01 ars0; L11 S01 ars1; L11 S01 ars2; L11 S01 ars3; L11 S01 ars4; L11 S01 ars5; L11 S02 ars0; L11 S02 ars1; L11 S02 ars2; L11 S02 ars3; L11 S02 ars4; L11 S02 ars5; L11 S03 ars0; L11 S03 ars1; L11 S03 ars2; L11 S03 ars3; L11 S03 ars4; L11 S03 ars5; L11 S04 ars0; L11 S04 ars1; L11 S04 ars2; L11 S04 ars3; L11 S04 ars4; L11 S04 ars5; L11 S05 ars0; L11 S05 ars1; L11 S05 ars2; L11 S05 ars3; L11 S05 ars4; L11 S05 ars5; L11 S06 ars0; L11 S06 ars1; L11 S06 ars2; L11 S06 ars3; L11 S06 ars4; L11 S06 ars5; L11 S07 ars0; L11 S07 ars1; L11 S07 ars2; L11 S07 ars3; L11 S07 ars4; L11 S07 ars5; L11 S08 ars0; L11 S08 ars1; L11 S08 ars2; L11 S08 ars3; L11 S08 ars4; L11 S08 ars5; L11 S09 ars0; L11 S09 ars1; L11 S09 ars2; L11 S09 ars3; L11 S09 ars4; L11 S09 ars5; L11 S10 ars0; L11 S10 ars1; L11 S10 ars2; L11 S10 ars3; L11 S10 ars4; L11 S10 ars5; L11 S11 ars0; L11 S11 ars1; ; ; ; ; ; ; L11 S12 ars2; L11 S12 ars3; ; ; ; ; ; ; L11 S13 ars4; L11 S13 ars5; ; ; L11 S14 ars2; L11 S14 ars3; L11 S14 ars4; L11 S14 ars5; ; ; L11 S15 ars2; L11 S15 ars3; L11 S15 ars4; L11 S15 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L11 S21 ars2; L11 S21 ars3; L11 S21 ars4; L11 S21 ars5; ; ; ; ; ; ; L11 S23 ars0; L11 S23 ars1; L11 S23 ars2; L11 S23 ars3; L11 S23 ars4; L11 S23 ars5; L11 S24 ars0; L11 S24 ars1; L11 S24 ars2; L11 S24 ars3; L11 S24 ars4; L11 S24 ars5; L11 S25 ars0; L11 S25 ars1; L11 S25 ars2; L11 S25 ars3; L11 S25 ars4; L11 S25 ars5; L12 S01 ars0; L12 S01 ars1; L12 S01 ars2; L12 S01 ars3; L12 S01 ars4; L12 S01 ars5; L12 S02 ars0; L12 S02 ars1; L12 S02 ars2; L12 S02 ars3; L12 S02 ars4; L12 S02 ars5; L12 S03 ars0; L12 S03 ars1; L12 S03 ars2; L12 S03 ars3; L12 S03 ars4; L12 S03 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L12 S07 ars4; L12 S07 ars5; ; ; ; ; L12 S08 ars4; L12 S08 ars5; ; ; ; ; ; ; L12 S10 ars0; L12 S10 ars1; ; ; ; ; ; ; ; ; L12 S11 ars4; L12 S11 ars5; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; L12 S15 ars0; L12 S15 ars1; ; ; ; ; ; ; ; ; ; ; L12 S17 ars0; L12 S17 ars1; L12 S17 ars2; L12 S17 ars3; L12 S17 ars4; L12 S17 ars5; L12 S18 ars0; L12 S18 ars1; L12 S18 ars2; L12 S18 ars3; L12 S18 ars4; L12 S18 ars5; L12 S19 ars0; L12 S19 ars1; L12 S19 ars2; L12 S19 ars3; L12 S19 ars4; L12 S19 ars5; L12 S20 ars0; L12 S20 ars1; L12 S20 ars2; L12 S20 ars3; L12 S20 ars4; L12 S20 ars5; /////////////////////////////////////////////////////////////////////////////////////////////////////////// Execution of intratical program: evalu155:agusanlo/macros/tical> ./intratical -i /l/agusanlo/data/tical/intratical_10/autobinning -o /l/agusanlo/data/tical/intratical_10 > Searching OB available... ID: 1628 (L01 S15) [ 1 run ] ID: 1631 (L01 S02) [ 1 run ] ID: 1621 (L01 S21) [ 1 run ] ID: 1643 (L01 S09) [ 1 run ] ID: 1065 (L02 S15) [ 1 run ] ID: 1095 (L02 S02) [ 1 run ] ID: 1118 (L02 S21) [ 1 run ] ID: 1048 (L02 S09) [ 1 run ] ID: 1140 (L03 S15) [ 1 run ] ID: 1027 (L03 S02) [ 1 run ] ID: 1106 (L03 S21) [ 1 run ] ID: 1157 (L03 S09) [ 1 run ] ID: 1115 (L04 S15) [ 1 run ] ID: 1091 (L04 S02) [ 1 run ] ID: 1151 (L04 S21) [ 1 run ] ID: 1141 (L04 S09) [ 1 run ] ID: 1163 (L05 S15) [ 1 run ] ID: 1193 (L05 S02) [ 1 run ] ID: 1158 (L05 S21) [ 1 run ] ID: 1159 (L05 S09) [ 1 run ] ID: 1046 (L06 S15) [ 1 run ] ID: 1092 (L06 S02) [ 1 run ] ID: 1056 (L06 S21) [ 1 run ] ID: 1186 (L06 S09) [ 1 run ] ID: 1042 (L07 S15) [ 1 run ] ID: 1195 (L07 S02) [ 1 run ] ID: 1177 (L07 S21) [ 1 run ] ID: 1116 (L07 S09) [ 1 run ] ID: 1138 (L08 S15) [ 1 run ] ID: 1232 (L08 S02) [ 1 run ] ID: 1219 (L08 S21) [ 1 run ] ID: 1176 (L08 S09) [ 1 run ] ID: 1068 (L09 S15) [ 1 run ] ID: 1025 (L09 S02) [ 1 run ] ID: 1247 (L09 S09) [ 1 run ] ID: 1249 (L10 S15) [ 1 run ] ID: 1242 (L10 S02) [ 1 run ] ID: 1277 (L10 S09) [ 1 run ] ID: 1272 (L11 S15) [ 1 run ] ID: 1309 (L11 S09) [ 1 run ] ID: 1088 (L12 S02) [ 1 run ] ID: 1038 (L12 S09) [ 1 run ] > Found 42 OBs! (in a total of 24 runes) >========================================================================================< >>> Calibrating Line 1: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1631 (L01 S02) > Fitting for time corrections... -> Fit: offset = -3.8 slope = 0.115 (parabola = -0.000205) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.633ns [*] · ars 3: +0.671ns [*] · ars 4: -0.653ns [*] · ars 5: -0.429ns [*] - Storey 5: · ars 0: -3.16ns [ ] · ars 1: -3.62ns [ ] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.0147ns [*] · ars 5: +0.0177ns [*] - Storey 6: · ars 0: +0.41ns [*] · ars 1: +0.356ns [*] · ars 2: -0.147ns [*] · ars 3: -0.0724ns [*] · ars 4: -0.0614ns [*] · ars 5: +0.0908ns [*] - Storey 7: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.93ns [*] · ars 3: +0.979ns [*] · ars 4: -0.351ns [*] · ars 5: -0.226ns [*] - Storey 8: · ars 0: -0.509ns [*] · ars 1: -0.553ns [*] · ars 2: -0.75ns [*] · ars 3: -0.559ns [*] · ars 4: -0.246ns [*] · ars 5: -0.0227ns [*] - Storey 9: · ars 0: -0.238ns [*] · ars 1: -0.154ns [*] · ars 2: -0.108ns [*] · ars 3: -0.658ns [*] · ars 4: -0.926ns [*] · ars 5: -0.436ns [*] - Storey 10: · ars 0: +1.79ns [*] · ars 1: +2.35ns [ ] · ars 2: +1.13ns [*] · ars 3: +0.796ns [*] · ars 4: -0.655ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line01_section1.png has been created · ars 5: -0.066ns [*] > Section #2: Calibrating from St11 to St16 using OB 1643 (L01 S09) > Fitting for time corrections... -> Fit: offset = -0.104 slope = 0.0913 (parabola = 0.000131) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: -0.0913ns [*] · ars 1: -0.266ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.0665ns [*] · ars 5: +0.0722ns [*] - Storey 12: · ars 0: -0.00402ns [*] · ars 1: -0.0177ns [*] · ars 2: -0.0769ns [*] · ars 3: +0.0227ns [*] · ars 4: -0.343ns [*] · ars 5: -0.401ns [*] - Storey 13: · ars 0: -0.206ns [*] · ars 1: -0.256ns [*] · ars 2: +0.657ns [*] · ars 3: +0.603ns [*] · ars 4: +0.0377ns [*] · ars 5: +0.275ns [*] - Storey 14: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.416ns [*] · ars 3: -0.256ns [*] · ars 4: +0.154ns [*] · ars 5: +0.134ns [*] - Storey 15: · ars 0: +0.415ns [*] · ars 1: +0.337ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.0681ns [*] · ars 5: -0.289ns [*] - Storey 16: · ars 0: +0.926ns [*] · ars 1: +0.581ns [*] · ars 2: +0.0853ns [*] · ars 3: -0.536ns [*] · ars 4: Not Available Info in : png file /l/agusanlo/data/tical/intratical_10/Line01_section2.png has been created · ars 5: Not Available > Section #3: Calibrating from St17 to St22 using OB 1628 (L01 S15) > Fitting for time corrections... -> Fit: offset = 0.299 slope = 0.0845 (parabola = 8.15e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.11ns [*] · ars 1: -0.0103ns [*] · ars 2: -0.597ns [*] · ars 3: -0.0623ns [*] · ars 4: +0.0936ns [*] · ars 5: -0.111ns [*] - Storey 18: · ars 0: -0.16ns [*] · ars 1: -0.097ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.131ns [*] · ars 5: +0.0625ns [*] - Storey 19: · ars 0: +1.19ns [*] · ars 1: +0.149ns [*] · ars 2: +0.0152ns [*] · ars 3: +0.429ns [*] · ars 4: +0.116ns [*] · ars 5: -0.0363ns [*] - Storey 20: · ars 0: -0.678ns [*] · ars 1: -0.353ns [*] · ars 2: +0.166ns [*] · ars 3: +0.148ns [*] · ars 4: -0.374ns [*] · ars 5: +0.384ns [*] - Storey 21: · ars 0: -0.203ns [*] · ars 1: +0.203ns [*] · ars 2: -0.127ns [*] · ars 3: +0.167ns [*] · ars 4: -0.795ns [*] · ars 5: -0.749ns [*] - Storey 22: · ars 0: +0.376ns [*] · ars 1: +0.152ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +1.19ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line01_section3.png has been created · ars 5: +1.04ns [*] > Section #4: Calibrating from St23 to St25 using OB 1621 (L01 S21) > Fitting for time corrections... -> Fit: offset = -1.16 slope = 0.104 (parabola = 0.00076) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: +0.122ns [*] · ars 1: +0.05ns [*] · ars 2: -0.248ns [*] · ars 3: -0.204ns [*] · ars 4: +0.138ns [*] · ars 5: -0.178ns [*] - Storey 24: · ars 0: +0.104ns [*] · ars 1: +0.0761ns [*] · ars 2: +0.236ns [*] · ars 3: +0.104ns [*] · ars 4: -0.19ns [*] · ars 5: +0.311ns [*] - Storey 25: · ars 0: -0.188ns [*] · ars 1: -0.15ns [*] · ars 2: -0.121ns [*] · ars 3: +0.379ns [*] · ars 4: -0.242ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line01_section4.png has been created · ars 5: +0.000181ns [*] >========================================================================================< >>> Calibrating Line 2: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1095 (L02 S02) > Fitting for time corrections... -> Fit: offset = -1.83 slope = 0.0546 (parabola = -0.000346) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.341ns [*] · ars 3: +0.111ns [*] · ars 4: +0.127ns [*] · ars 5: +0.142ns [*] - Storey 5: · ars 0: +0.431ns [*] · ars 1: +0.342ns [*] · ars 2: +0.365ns [*] · ars 3: +0.262ns [*] · ars 4: +0.514ns [*] · ars 5: +0.401ns [*] - Storey 6: · ars 0: -0.63ns [*] · ars 1: -0.558ns [*] · ars 2: -0.676ns [*] · ars 3: -0.208ns [*] · ars 4: -0.456ns [*] · ars 5: -0.369ns [*] - Storey 7: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.368ns [*] · ars 3: -0.427ns [*] · ars 4: -0.421ns [*] · ars 5: -0.627ns [*] - Storey 8: · ars 0: -0.169ns [*] · ars 1: -0.209ns [*] · ars 2: +0.0174ns [*] · ars 3: +0.189ns [*] · ars 4: +0.231ns [*] · ars 5: -0.409ns [*] - Storey 9: · ars 0: -5.42ns [ ] · ars 1: -5.95ns [ ] · ars 2: -0.147ns [*] · ars 3: +0.751ns [*] · ars 4: +0.51ns [*] · ars 5: +0.798ns [*] - Storey 10: · ars 0: Not Available · ars 1: Not Available · ars 2: -3.61ns [ ] · ars 3: -3.69ns [ ] · ars 4: +0.104ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line02_section1.png has been created · ars 5: +0.0388ns [*] > Section #2: Calibrating from St11 to St16 using OB 1048 (L02 S09) > Fitting for time corrections... -> Fit: offset = -1.21 slope = 0.0644 (parabola = -9.26e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: +0.143ns [ ] · ars 1: +0.213ns [*] · ars 2: -0.0758ns [*] · ars 3: +0.124ns [*] · ars 4: -0.0862ns [*] · ars 5: +0.0351ns [*] - Storey 12: · ars 0: -0.457ns [*] · ars 1: -0.578ns [*] · ars 2: +0.125ns [*] · ars 3: +0.162ns [*] · ars 4: +0.0503ns [*] · ars 5: +0.248ns [*] - Storey 13: · ars 0: +0.339ns [*] · ars 1: +0.203ns [*] · ars 2: +0.145ns [*] · ars 3: -0.052ns [*] · ars 4: +0.359ns [*] · ars 5: +0.91ns [*] - Storey 14: · ars 0: +0.212ns [*] · ars 1: +0.281ns [*] · ars 2: -0.982ns [*] · ars 3: -0.889ns [*] · ars 4: -0.0698ns [*] · ars 5: +0.00699ns [*] - Storey 15: · ars 0: -0.255ns [*] · ars 1: -0.137ns [*] · ars 2: -0.511ns [*] · ars 3: -0.00969ns [*] · ars 4: -0.108ns [*] · ars 5: -0.0847ns [*] - Storey 16: · ars 0: +0.287ns [*] · ars 1: +0.0598ns [*] · ars 2: -0.0983ns [*] · ars 3: +0.498ns [*] · ars 4: -0.603ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line02_section2.png has been created · ars 5: -0.248ns [*] > Section #3: Calibrating from St17 to St22 using OB 1065 (L02 S15) > Fitting for time corrections... -> Fit: offset = -1.83 slope = 0.0716 (parabola = -9.76e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.569ns [*] · ars 1: +0.266ns [*] · ars 2: -0.208ns [*] · ars 3: -0.125ns [ ] · ars 4: -0.631ns [*] · ars 5: -0.601ns [*] - Storey 18: · ars 0: +0.0455ns [*] · ars 1: -0.195ns [*] · ars 2: +0.229ns [*] · ars 3: +0.427ns [*] · ars 4: +0.0114ns [*] · ars 5: -0.248ns [*] - Storey 19: · ars 0: -0.303ns [*] · ars 1: -0.0228ns [*] · ars 2: +1.75ns [*] · ars 3: +1.51ns [*] · ars 4: +3.65ns [ ] · ars 5: +3.73ns [ ] - Storey 20: · ars 0: +1.07ns [*] · ars 1: +0.638ns [*] · ars 2: +0.179ns [*] · ars 3: +0.232ns [*] · ars 4: -1.97ns [*] · ars 5: -1.61ns [*] - Storey 21: · ars 0: -0.447ns [*] · ars 1: -0.534ns [*] · ars 2: -0.177ns [*] · ars 3: -0.15ns [*] · ars 4: -0.521ns [*] · ars 5: -0.265ns [*] - Storey 22: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.129ns [*] · ars 3: -0.321ns [*] · ars 4: -0.417ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line02_section3.png has been created · ars 5: -0.281ns [*] > Section #4: Calibrating from St23 to St25 using OB 1118 (L02 S21) > Fitting for time corrections... -> Fit: offset = -8.16 slope = 0.169 (parabola = 0.00418) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: +0.0604ns [*] · ars 1: +0.0719ns [*] · ars 2: -0.00606ns [*] · ars 3: -0.22ns [*] · ars 4: -0.801ns [*] · ars 5: -0.853ns [*] - Storey 24: · ars 0: +0.115ns [*] · ars 1: +0.378ns [*] · ars 2: +0.88ns [*] · ars 3: +0.73ns [*] · ars 4: +0.522ns [*] · ars 5: +0.879ns [*] - Storey 25: · ars 0: +0.0407ns [*] · ars 1: +0.35ns [*] · ars 2: -0.0923ns [*] · ars 3: +0.00276ns [*] · ars 4: -0.732ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line02_section4.png has been created · ars 5: -1.33ns [*] >========================================================================================< >>> Calibrating Line 3: > Section #0: Calibrating from St01 to St03 using OB 1193 (L05 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1027 (L03 S02) > Fitting for time corrections... -> Fit: offset = -4.21 slope = 0.0786 (parabola = -4.73e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: -0.0923ns [*] · ars 1: -0.213ns [*] · ars 2: +0.0683ns [*] · ars 3: -0.157ns [*] · ars 4: -0.303ns [*] · ars 5: -0.335ns [*] - Storey 5: · ars 0: +0.0173ns [*] · ars 1: +0.175ns [*] · ars 2: +0.835ns [*] · ars 3: +0.566ns [*] · ars 4: +0.389ns [*] · ars 5: -0.00494ns [*] - Storey 6: · ars 0: -0.111ns [*] · ars 1: +0.22ns [*] · ars 2: -0.59ns [*] · ars 3: -0.566ns [*] · ars 4: +0.478ns [*] · ars 5: +0.759ns [*] - Storey 7: · ars 0: -0.158ns [*] · ars 1: -0.374ns [*] · ars 2: -0.139ns [*] · ars 3: -0.155ns [*] · ars 4: +0.45ns [*] · ars 5: +0.0223ns [*] - Storey 8: · ars 0: +0.446ns [*] · ars 1: -0.0869ns [*] · ars 2: -1.26ns [*] · ars 3: -1.56ns [*] · ars 4: +0.532ns [*] · ars 5: +0.0692ns [*] - Storey 9: · ars 0: +0.0644ns [*] · ars 1: -0.0799ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.0496ns [*] · ars 5: +0.379ns [*] - Storey 10: · ars 0: -0.0508ns [*] · ars 1: +0.114ns [*] · ars 2: +0.79ns [*] · ars 3: -0.0629ns [*] · ars 4: +0.164ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line03_section1.png has been created · ars 5: -0.196ns [*] > Section #2: Calibrating from St11 to St16 using OB 1157 (L03 S09) > Fitting for time corrections... -> Fit: offset = -5.69 slope = 0.0715 (parabola = 3.63e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.238ns [*] · ars 3: -0.233ns [*] · ars 4: -0.0729ns [*] · ars 5: -0.125ns [*] - Storey 12: · ars 0: -0.324ns [*] · ars 1: -0.367ns [*] · ars 2: +0.0967ns [*] · ars 3: +0.213ns [*] · ars 4: -0.21ns [*] · ars 5: -0.182ns [*] - Storey 13: · ars 0: -0.37ns [*] · ars 1: -0.588ns [*] · ars 2: +1.25ns [*] · ars 3: +1.01ns [*] · ars 4: +0.44ns [*] · ars 5: +0.736ns [*] - Storey 14: · ars 0: -0.101ns [*] · ars 1: -0.0372ns [*] · ars 2: -95.7ns [ ] · ars 3: -95.2ns [ ] · ars 4: +0.2ns [*] · ars 5: +0.219ns [*] - Storey 15: · ars 0: +0.0694ns [*] · ars 1: -0.0216ns [*] · ars 2: -3.25ns [ ] · ars 3: -4.87ns [ ] · ars 4: +0.241ns [*] · ars 5: +0.404ns [*] - Storey 16: · ars 0: -0.0251ns [*] · ars 1: +0.196ns [*] · ars 2: -1.32ns [*] · ars 3: -1.38ns [*] · ars 4: -1.03ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line03_section2.png has been created · ars 5: -0.703ns [*] > Section #3: Calibrating from St17 to St22 using OB 1140 (L03 S15) > Fitting for time corrections... -> Fit: offset = -5.03 slope = 0.0639 (parabola = -2.72e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: -0.178ns [*] · ars 1: +0.0671ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.131ns [*] · ars 5: +0.154ns [*] - Storey 18: · ars 0: -0.192ns [*] · ars 1: -0.343ns [*] · ars 2: +0.511ns [*] · ars 3: +0.306ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 19: · ars 0: -0.0213ns [*] · ars 1: -0.0623ns [*] · ars 2: -0.111ns [*] · ars 3: -0.136ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 20: · ars 0: -0.0251ns [*] · ars 1: -0.49ns [*] · ars 2: +0.0464ns [*] · ars 3: +0.32ns [*] · ars 4: -0.405ns [*] · ars 5: -0.428ns [*] - Storey 21: · ars 0: -0.12ns [*] · ars 1: -0.213ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.536ns [*] · ars 5: +0.497ns [*] - Storey 22: · ars 0: +0.263ns [*] · ars 1: +0.693ns [*] · ars 2: -0.00224ns [*] · ars 3: -0.531ns [*] · ars 4: Not Available Info in : png file /l/agusanlo/data/tical/intratical_10/Line03_section3.png has been created · ars 5: Not Available > Section #4: Calibrating from St23 to St25 using OB 1106 (L03 S21) > Fitting for time corrections... -> Fit: offset = -9.7 slope = 0.187 (parabola = 0.000382) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: -0.0769ns [*] · ars 1: +0.0216ns [*] · ars 2: +0.0703ns [*] · ars 3: +0.153ns [*] · ars 4: -0.272ns [*] · ars 5: -0.0447ns [*] - Storey 24: · ars 0: -0.146ns [*] · ars 1: +0.167ns [*] · ars 2: +0.496ns [*] · ars 3: -0.0203ns [*] · ars 4: -0.324ns [*] · ars 5: +0.126ns [*] - Storey 25: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.252ns [*] · ars 3: +0.17ns [*] · ars 4: +0.0268ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line03_section4.png has been created · ars 5: -0.094ns [*] >========================================================================================< >>> Calibrating Line 4: > Section #0: Calibrating from St01 to St03 using OB 1092 (L06 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1091 (L04 S02) > Fitting for time corrections... -> Fit: offset = 1.29 slope = 0.0104 (parabola = 0.000158) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: -0.13ns [*] · ars 1: -0.00136ns [ ] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.342ns [*] · ars 5: -0.289ns [*] - Storey 5: · ars 0: -0.0699ns [*] · ars 1: -0.042ns [*] · ars 2: -0.0638ns [*] · ars 3: -0.0775ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 6: · ars 0: +0.249ns [*] · ars 1: +0.136ns [*] · ars 2: -3.81ns [ ] · ars 3: -3.79ns [ ] · ars 4: +0.719ns [*] · ars 5: +0.631ns [*] - Storey 7: · ars 0: -2.64ns [ ] · ars 1: -2.27ns [ ] · ars 2: -0.484ns [*] · ars 3: -0.72ns [*] · ars 4: -0.584ns [*] · ars 5: -0.0909ns [*] - Storey 8: · ars 0: +0.523ns [*] · ars 1: +0.235ns [*] · ars 2: -0.163ns [*] · ars 3: -0.0318ns [*] · ars 4: +1.64ns [*] · ars 5: +1.17ns [*] - Storey 9: · ars 0: -0.161ns [*] · ars 1: +0.0453ns [*] · ars 2: -0.938ns [*] · ars 3: -1.14ns [*] · ars 4: -0.0919ns [*] · ars 5: +0.069ns [*] - Storey 10: · ars 0: -0.336ns [*] · ars 1: -0.112ns [*] · ars 2: +4.5ns [ ] · ars 3: +1.89ns [*] · ars 4: -1.25ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line04_section1.png has been created · ars 5: -0.188ns [*] > Section #2: Calibrating from St11 to St16 using OB 1141 (L04 S09) > Fitting for time corrections... -> Fit: offset = -2.75 slope = 0.0905 (parabola = -1.52e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: -0.263ns [*] · ars 1: -44.2ns [ ] · ars 2: +0.229ns [*] · ars 3: +0.488ns [*] · ars 4: +0.0188ns [*] · ars 5: -0.0341ns [*] - Storey 12: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available - Storey 13: · ars 0: -1.18ns [*] · ars 1: -1.02ns [*] · ars 2: +0.372ns [*] · ars 3: +0.795ns [*] · ars 4: -0.192ns [*] · ars 5: +0.188ns [*] - Storey 14: · ars 0: -0.279ns [*] · ars 1: -0.238ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.0161ns [*] · ars 5: -0.259ns [*] - Storey 15: · ars 0: +0.522ns [*] · ars 1: +0.536ns [*] · ars 2: +0.498ns [*] · ars 3: +0.951ns [*] · ars 4: -0.141ns [*] · ars 5: +0.21ns [*] - Storey 16: · ars 0: -0.116ns [*] · ars 1: -0.132ns [*] · ars 2: -0.122ns [*] · ars 3: -0.507ns [*] · ars 4: -0.0894ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line04_section2.png has been created · ars 5: -0.379ns [*] > Section #3: Calibrating from St17 to St22 using OB 1115 (L04 S15) > Fitting for time corrections... -> Fit: offset = -3.66 slope = 0.0788 (parabola = 4.21e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: -0.0334ns [*] · ars 1: +0.0986ns [*] · ars 2: +0.0716ns [*] · ars 3: +0.247ns [*] · ars 4: -0.78ns [ ] · ars 5: -45.9ns [ ] - Storey 18: · ars 0: -0.492ns [*] · ars 1: -0.807ns [*] · ars 2: -0.245ns [*] · ars 3: -0.334ns [*] · ars 4: -0.443ns [*] · ars 5: -0.0631ns [*] - Storey 19: · ars 0: +1.6ns [*] · ars 1: +1.42ns [*] · ars 2: -0.166ns [*] · ars 3: -0.107ns [*] · ars 4: +0.403ns [*] · ars 5: +0.637ns [*] - Storey 20: · ars 0: -0.165ns [*] · ars 1: -0.335ns [*] · ars 2: -0.58ns [*] · ars 3: -0.286ns [*] · ars 4: -0.705ns [*] · ars 5: -0.26ns [*] - Storey 21: · ars 0: -0.144ns [*] · ars 1: +0.467ns [*] · ars 2: +0.138ns [*] · ars 3: -0.11ns [*] · ars 4: +0.157ns [*] · ars 5: +0.0567ns [*] - Storey 22: · ars 0: -0.286ns [*] · ars 1: +0.157ns [*] · ars 2: -0.0613ns [*] · ars 3: +0.0618ns [*] · ars 4: +0.244ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line04_section3.png has been created · ars 5: +0.187ns [*] > Section #4: Calibrating from St23 to St25 using OB 1151 (L04 S21) > Fitting for time corrections... -> Fit: offset = -5.22 slope = 0.146 (parabola = 0.00235) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: +2.78ns [ ] · ars 1: +2.48ns [ ] · ars 2: +0.285ns [*] · ars 3: +0.224ns [*] · ars 4: -0.877ns [*] · ars 5: -0.547ns [*] - Storey 24: · ars 0: +0.153ns [*] · ars 1: +0.265ns [*] · ars 2: +0.331ns [*] · ars 3: +0.481ns [*] · ars 4: +0.58ns [*] · ars 5: +0.0191ns [*] - Storey 25: · ars 0: -1.39ns [*] · ars 1: -1.6ns [*] · ars 2: +1.36ns [*] · ars 3: +1.31ns [*] · ars 4: -0.378ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line04_section4.png has been created · ars 5: -0.206ns [*] >========================================================================================< >>> Calibrating Line 5: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1193 (L05 S02) > Fitting for time corrections... -> Fit: offset = -6.25 slope = 0.0629 (parabola = -0.000111) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: -0.188ns [*] · ars 1: +0.111ns [*] · ars 2: +0.536ns [*] · ars 3: +0.273ns [*] · ars 4: +0.094ns [*] · ars 5: -0.0268ns [*] - Storey 5: · ars 0: -0.133ns [*] · ars 1: +0.054ns [*] · ars 2: +0.0398ns [*] · ars 3: +0.102ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 6: · ars 0: -0.00377ns [*] · ars 1: -0.0818ns [*] · ars 2: -0.0153ns [*] · ars 3: +0.0499ns [*] · ars 4: -0.57ns [*] · ars 5: -0.354ns [*] - Storey 7: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.151ns [*] · ars 3: +0.354ns [*] · ars 4: -0.0913ns [*] · ars 5: -0.15ns [*] - Storey 8: · ars 0: -0.396ns [*] · ars 1: -0.196ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.713ns [*] · ars 5: -1ns [*] - Storey 9: · ars 0: +0.343ns [*] · ars 1: +0.167ns [*] · ars 2: +0.167ns [*] · ars 3: +0.0834ns [*] · ars 4: +1.16ns [*] · ars 5: +0.706ns [*] - Storey 10: · ars 0: -0.279ns [*] · ars 1: -0.211ns [*] · ars 2: -0.271ns [*] · ars 3: -0.279ns [*] · ars 4: +0.436ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line05_section1.png has been created · ars 5: +0.142ns [*] > Section #2: Calibrating from St11 to St16 using OB 1159 (L05 S09) > Fitting for time corrections... -> Fit: offset = -8.71 slope = 0.095 (parabola = 6.29e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: +0.408ns [*] · ars 1: -0.0472ns [*] · ars 2: +0.0677ns [*] · ars 3: +0.443ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 12: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.419ns [*] · ars 3: +0.449ns [*] · ars 4: -1.61ns [*] · ars 5: -1.6ns [*] - Storey 13: · ars 0: +0.162ns [*] · ars 1: +0.422ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.167ns [*] · ars 5: +0.111ns [*] - Storey 14: · ars 0: -0.34ns [*] · ars 1: -0.216ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.916ns [*] · ars 5: +1.22ns [*] - Storey 15: · ars 0: -0.251ns [*] · ars 1: -0.16ns [*] · ars 2: -0.479ns [*] · ars 3: -0.0119ns [*] · ars 4: +0.385ns [*] · ars 5: +0.342ns [*] - Storey 16: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available Info in : png file /l/agusanlo/data/tical/intratical_10/Line05_section2.png has been created · ars 5: Not Available > Section #3: Calibrating from St17 to St22 using OB 1163 (L05 S15) > Fitting for time corrections... -> Fit: offset = -3.52 slope = 0.0474 (parabola = -0.00011) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: -0.295ns [*] · ars 1: +0.147ns [*] · ars 2: +0.164ns [*] · ars 3: +0.156ns [ ] · ars 4: +0.289ns [*] · ars 5: +0.318ns [ ] - Storey 18: · ars 0: +0.123ns [*] · ars 1: +0.0729ns [*] · ars 2: +0.14ns [*] · ars 3: -0.18ns [*] · ars 4: +0.188ns [*] · ars 5: +0.416ns [*] - Storey 19: · ars 0: Not Available · ars 1: Not Available · ars 2: -1.14ns [*] · ars 3: -0.834ns [*] · ars 4: +0.502ns [*] · ars 5: +0.38ns [*] - Storey 20: · ars 0: -0.173ns [*] · ars 1: -0.139ns [*] · ars 2: -0.229ns [*] · ars 3: -0.108ns [*] · ars 4: +0.18ns [*] · ars 5: +0.161ns [*] - Storey 21: · ars 0: -0.192ns [*] · ars 1: -0.0197ns [*] · ars 2: -0.16ns [*] · ars 3: -0.369ns [*] · ars 4: +0.432ns [*] · ars 5: +0.606ns [*] - Storey 22: · ars 0: -0.446ns [*] · ars 1: -0.89ns [*] · ars 2: +0.223ns [*] · ars 3: +0.164ns [*] · ars 4: Not Available Info in : png file /l/agusanlo/data/tical/intratical_10/Line05_section3.png has been created · ars 5: Not Available > Section #4: Calibrating from St23 to St25 using OB 1158 (L05 S21) > Fitting for time corrections... -> Fit: offset = -31.4 slope = 0.952 (parabola = 0.0495) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: -0.373ns [*] · ars 1: -0.406ns [*] · ars 2: -0.457ns [*] · ars 3: -0.433ns [*] · ars 4: +0.821ns [*] · ars 5: +0.847ns [*] - Storey 24: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: +10.7ns [ ] · ars 5: +10.4ns [ ] - Storey 25: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.286ns [*] · ars 3: +0.286ns [*] · ars 4: Not Available Info in : png file /l/agusanlo/data/tical/intratical_10/Line05_section4.png has been created · ars 5: Not Available >========================================================================================< >>> Calibrating Line 6: > Section #0: Calibrating from St01 to St03 using OB 1091 (L04 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1092 (L06 S02) > Fitting for time corrections... -> Fit: offset = -2.96 slope = 0.0866 (parabola = -0.00052) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: +1.27ns [*] · ars 1: +1.5ns [*] · ars 2: +0.0972ns [*] · ars 3: +0.0796ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 5: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available - Storey 6: · ars 0: +0.0777ns [*] · ars 1: -0.144ns [*] · ars 2: -1.04ns [*] · ars 3: -1.21ns [*] · ars 4: -0.11ns [*] · ars 5: +0.166ns [*] - Storey 7: · ars 0: -0.51ns [*] · ars 1: -0.483ns [*] · ars 2: +0.84ns [*] · ars 3: -0.624ns [*] · ars 4: -0.459ns [*] · ars 5: -0.414ns [*] - Storey 8: · ars 0: +0.0548ns [*] · ars 1: -0.44ns [*] · ars 2: -0.481ns [*] · ars 3: -0.568ns [*] · ars 4: +0.219ns [*] · ars 5: -0.329ns [*] - Storey 9: · ars 0: +0.184ns [*] · ars 1: -0.0677ns [*] · ars 2: +0.403ns [*] · ars 3: +0.157ns [*] · ars 4: -0.832ns [*] · ars 5: -0.451ns [*] - Storey 10: · ars 0: +0.174ns [*] · ars 1: +0.239ns [*] · ars 2: -0.164ns [*] · ars 3: +0.31ns [*] · ars 4: +1.59ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line06_section1.png has been created · ars 5: +0.96ns [*] > Section #2: Calibrating from St11 to St16 using OB 1186 (L06 S09) > Fitting for time corrections... -> Fit: offset = -4.24 slope = 0.0753 (parabola = -0.000401) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: +0.0644ns [*] · ars 1: +0.187ns [*] · ars 2: +0.546ns [*] · ars 3: +0.35ns [*] · ars 4: +0.121ns [*] · ars 5: +0.242ns [*] - Storey 12: · ars 0: +0.499ns [*] · ars 1: +0.38ns [*] · ars 2: +0.365ns [*] · ars 3: +0.773ns [*] · ars 4: -0.351ns [*] · ars 5: -0.415ns [*] - Storey 13: · ars 0: -1.79ns [*] · ars 1: -0.867ns [*] · ars 2: -31.4ns [ ] · ars 3: -30.6ns [ ] · ars 4: -0.0456ns [*] · ars 5: -0.147ns [*] - Storey 14: · ars 0: +0.204ns [*] · ars 1: +0.411ns [*] · ars 2: +0.193ns [*] · ars 3: +0.871ns [*] · ars 4: +0.0847ns [*] · ars 5: -0.152ns [*] - Storey 15: · ars 0: -1ns [*] · ars 1: -1.17ns [*] · ars 2: -0.561ns [*] · ars 3: -0.525ns [*] · ars 4: -6.98ns [ ] · ars 5: -6.61ns [ ] - Storey 16: · ars 0: -0.737ns [*] · ars 1: -0.749ns [*] · ars 2: -0.274ns [*] · ars 3: -0.447ns [*] · ars 4: +0.0467ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line06_section2.png has been created · ars 5: -0.057ns [*] > Section #3: Calibrating from St17 to St22 using OB 1046 (L06 S15) > Fitting for time corrections... -> Fit: offset = 1.58 slope = 0.0741 (parabola = -0.000534) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.312ns [*] · ars 1: +0.454ns [*] · ars 2: +0.353ns [*] · ars 3: +0.726ns [*] · ars 4: +1.51ns [*] · ars 5: +1.44ns [*] - Storey 18: · ars 0: -1.31ns [*] · ars 1: -0.92ns [*] · ars 2: -0.272ns [*] · ars 3: -0.276ns [*] · ars 4: +0.137ns [*] · ars 5: +0.15ns [*] - Storey 19: · ars 0: -1.73ns [*] · ars 1: -1.9ns [*] · ars 2: -2.43ns [ ] · ars 3: -2.4ns [ ] · ars 4: +1.22ns [*] · ars 5: +0.828ns [*] - Storey 20: · ars 0: -0.212ns [*] · ars 1: -0.369ns [*] · ars 2: -1.12ns [*] · ars 3: -0.853ns [*] · ars 4: -0.46ns [*] · ars 5: -0.387ns [*] - Storey 21: · ars 0: -0.374ns [*] · ars 1: -0.0784ns [*] · ars 2: +0.0508ns [*] · ars 3: +0.316ns [*] · ars 4: +0.0509ns [*] · ars 5: +0.026ns [*] - Storey 22: · ars 0: +0.0328ns [*] · ars 1: +0.26ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.141ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line06_section3.png has been created · ars 5: -0.198ns [*] > Section #4: Calibrating from St23 to St25 using OB 1056 (L06 S21) > Fitting for time corrections... -> Fit: offset = -7.21 slope = 0.186 (parabola = -0.000819) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: +0.497ns [*] · ars 1: +0.689ns [*] · ars 2: -0.814ns [*] · ars 3: -1.27ns [*] · ars 4: +0.818ns [*] · ars 5: +0.398ns [*] - Storey 24: · ars 0: -0.164ns [*] · ars 1: -0.409ns [*] · ars 2: +0.0133ns [*] · ars 3: +0.0887ns [*] · ars 4: -0.245ns [*] · ars 5: +0.0786ns [*] - Storey 25: · ars 0: +0.0895ns [*] · ars 1: -0.202ns [*] · ars 2: +0.106ns [*] · ars 3: +0.325ns [*] · ars 4: Not Available Info in : png file /l/agusanlo/data/tical/intratical_10/Line06_section4.png has been created · ars 5: Not Available >========================================================================================< >>> Calibrating Line 7: > Section #0: Calibrating from St01 to St03 using OB 1025 (L09 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1195 (L07 S02) > Fitting for time corrections... -> Fit: offset = -6.4 slope = 0.0805 (parabola = -0.000139) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: +0.13ns [*] · ars 1: +0.253ns [*] · ars 2: -26.8ns [ ] · ars 3: -31.9ns [ ] · ars 4: +0.0348ns [*] · ars 5: -0.161ns [*] - Storey 5: · ars 0: +0.151ns [*] · ars 1: +0.272ns [*] · ars 2: -0.265ns [*] · ars 3: -0.434ns [*] · ars 4: -0.114ns [*] · ars 5: -0.0224ns [*] - Storey 6: · ars 0: +0.56ns [*] · ars 1: +0.59ns [*] · ars 2: +0.0475ns [*] · ars 3: +0.0176ns [*] · ars 4: +0.139ns [*] · ars 5: +0.138ns [*] - Storey 7: · ars 0: +0.102ns [*] · ars 1: -0.0218ns [*] · ars 2: -0.0467ns [*] · ars 3: +0.11ns [*] · ars 4: -0.337ns [*] · ars 5: +0.0459ns [*] - Storey 8: · ars 0: +0.151ns [*] · ars 1: -0.0775ns [*] · ars 2: -0.829ns [*] · ars 3: -1.25ns [*] · ars 4: +0.0578ns [*] · ars 5: +0.239ns [*] - Storey 9: · ars 0: -0.682ns [*] · ars 1: -0.0421ns [*] · ars 2: -0.838ns [*] · ars 3: -0.4ns [*] · ars 4: +0.216ns [*] · ars 5: +0.169ns [*] - Storey 10: · ars 0: -0.0671ns [*] · ars 1: +0.163ns [*] · ars 2: +0.815ns [*] · ars 3: +0.583ns [*] · ars 4: +0.126ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line07_section1.png has been created · ars 5: +0.481ns [*] > Section #2: Calibrating from St11 to St16 using OB 1116 (L07 S09) > Fitting for time corrections... -> Fit: offset = -3.51 slope = 0.0631 (parabola = -0.000205) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.578ns [*] · ars 3: -0.366ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 12: · ars 0: -0.17ns [*] · ars 1: -0.302ns [*] · ars 2: +1.94ns [*] · ars 3: +1.8ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 13: · ars 0: -0.17ns [*] · ars 1: -0.304ns [*] · ars 2: -0.112ns [*] · ars 3: -0.676ns [*] · ars 4: -71.5ns [ ] · ars 5: -73.2ns [ ] - Storey 14: · ars 0: +0.36ns [*] · ars 1: +0.0519ns [*] · ars 2: -0.289ns [*] · ars 3: -0.00199ns [*] · ars 4: -0.802ns [*] · ars 5: -0.475ns [*] - Storey 15: · ars 0: +0.0113ns [*] · ars 1: -0.185ns [*] · ars 2: -0.0919ns [*] · ars 3: +0.00248ns [*] · ars 4: -0.462ns [*] · ars 5: -0.764ns [*] - Storey 16: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: +0.482ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line07_section2.png has been created · ars 5: +0.319ns [*] > Section #3: Calibrating from St17 to St22 using OB 1042 (L07 S15) > Fitting for time corrections... -> Fit: offset = -3.69 slope = 0.0722 (parabola = 8.8e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.199ns [*] · ars 3: +0.424ns [*] · ars 4: -0.56ns [*] · ars 5: -0.15ns [*] - Storey 18: · ars 0: -0.0187ns [*] · ars 1: -0.0606ns [*] · ars 2: -0.0197ns [*] · ars 3: +0.103ns [*] · ars 4: +0.418ns [*] · ars 5: +0.211ns [*] - Storey 19: · ars 0: -0.906ns [*] · ars 1: -0.378ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.19ns [*] · ars 5: -0.464ns [*] - Storey 20: · ars 0: Not Available · ars 1: Not Available · ars 2: Not Available · ars 3: Not Available · ars 4: +0.469ns [*] · ars 5: +0.481ns [*] - Storey 21: · ars 0: +0.747ns [*] · ars 1: +0.366ns [*] · ars 2: -0.0912ns [*] · ars 3: -0.0786ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 22: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.81ns [*] · ars 3: -0.0384ns [*] · ars 4: -0.0539ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line07_section3.png has been created · ars 5: -0.352ns [*] > Section #4: Calibrating from St23 to St25 using OB 1177 (L07 S21) > Fitting for time corrections... -> Fit: offset = -3.53 slope = 0.0385 (parabola = -0.00102) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: -0.769ns [*] · ars 1: -0.465ns [*] · ars 2: +0.796ns [*] · ars 3: +0.808ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 24: · ars 0: +0.0222ns [*] · ars 1: +0.116ns [*] · ars 2: -0.0573ns [*] · ars 3: -0.287ns [*] · ars 4: -0.285ns [*] · ars 5: -0.248ns [*] - Storey 25: · ars 0: -0.561ns [*] · ars 1: -0.531ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.78ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line07_section4.png has been created · ars 5: +0.681ns [*] >========================================================================================< >>> Calibrating Line 8: > Section #0: Calibrating from St01 to St03 using OB 1242 (L10 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1232 (L08 S02) > Fitting for time corrections... -> Fit: offset = 0.673 slope = 0.0598 (parabola = -0.000206) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: -0.482ns [*] · ars 1: -0.469ns [*] · ars 2: +0.344ns [*] · ars 3: +0.374ns [*] · ars 4: +0.255ns [*] · ars 5: +0.151ns [*] - Storey 5: · ars 0: +0.377ns [*] · ars 1: +0.272ns [*] · ars 2: -0.0801ns [*] · ars 3: -0.312ns [*] · ars 4: +0.163ns [*] · ars 5: +0.394ns [*] - Storey 6: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.347ns [*] · ars 3: +0.273ns [*] · ars 4: +0.548ns [*] · ars 5: +0.242ns [*] - Storey 7: · ars 0: -0.0846ns [*] · ars 1: +0.563ns [*] · ars 2: -1.45ns [*] · ars 3: -1.73ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 8: · ars 0: +0.0633ns [*] · ars 1: -0.0517ns [*] · ars 2: -1ns [*] · ars 3: -0.847ns [*] · ars 4: +0.129ns [*] · ars 5: +0.366ns [*] - Storey 9: · ars 0: -0.198ns [*] · ars 1: +0.0123ns [*] · ars 2: -0.267ns [*] · ars 3: +0.493ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 10: · ars 0: -0.264ns [*] · ars 1: +0.0619ns [*] · ars 2: +1.01ns [*] · ars 3: +0.819ns [*] · ars 4: +0.16ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line08_section1.png has been created · ars 5: -0.179ns [*] > Section #2: Calibrating from St11 to St16 using OB 1176 (L08 S09) > Fitting for time corrections... -> Fit: offset = -0.386 slope = 0.0404 (parabola = 0.000448) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: -0.413ns [*] · ars 1: -0.195ns [*] · ars 2: -0.265ns [*] · ars 3: -0.452ns [*] · ars 4: -0.336ns [*] · ars 5: -0.164ns [*] - Storey 12: · ars 0: -1.23ns [*] · ars 1: -1.15ns [*] · ars 2: +1.31ns [*] · ars 3: +1.17ns [*] · ars 4: +0.137ns [*] · ars 5: +0.377ns [*] - Storey 13: · ars 0: -0.308ns [*] · ars 1: -0.142ns [*] · ars 2: +0.00727ns [*] · ars 3: -0.0728ns [*] · ars 4: -0.178ns [*] · ars 5: -0.387ns [*] - Storey 14: · ars 0: +1.69ns [*] · ars 1: +1.62ns [*] · ars 2: -0.579ns [*] · ars 3: -0.352ns [*] · ars 4: +2.61ns [ ] · ars 5: +2.36ns [ ] - Storey 15: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.162ns [*] · ars 3: +0.131ns [*] · ars 4: +1.8ns [*] · ars 5: +2.39ns [ ] - Storey 16: · ars 0: +1.63ns [*] · ars 1: +1.2ns [*] · ars 2: -0.836ns [*] · ars 3: -1.01ns [*] · ars 4: -0.258ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line08_section2.png has been created · ars 5: +0.13ns [*] > Section #3: Calibrating from St17 to St22 using OB 1138 (L08 S15) > Fitting for time corrections... -> Fit: offset = -1.24 slope = 0.0809 (parabola = -3.49e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.655ns [*] · ars 3: +0.601ns [*] · ars 4: +0.038ns [*] · ars 5: -0.423ns [*] - Storey 18: · ars 0: +0.244ns [*] · ars 1: +0.382ns [*] · ars 2: +4.04ns [ ] · ars 3: +3.83ns [ ] · ars 4: -0.197ns [*] · ars 5: -0.424ns [*] - Storey 19: · ars 0: -1.74ns [*] · ars 1: -1.66ns [*] · ars 2: -0.299ns [*] · ars 3: +0.145ns [*] · ars 4: +0.088ns [*] · ars 5: +0.229ns [*] - Storey 20: · ars 0: +0.153ns [*] · ars 1: +0.183ns [*] · ars 2: +1.18ns [*] · ars 3: +1.13ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 21: · ars 0: -0.0463ns [*] · ars 1: -0.371ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.00367ns [*] · ars 5: +0.205ns [*] - Storey 22: · ars 0: -0.0961ns [*] · ars 1: -0.164ns [*] · ars 2: -0.101ns [*] · ars 3: +0.285ns [*] · ars 4: -0.0395ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line08_section3.png has been created · ars 5: +0.27ns [*] > Section #4: Calibrating from St23 to St25 using OB 1219 (L08 S21) > Fitting for time corrections... -> Fit: offset = -3.06 slope = 0.132 (parabola = -0.00121) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 23: · ars 0: +0.621ns [ ] · ars 1: +0.137ns [*] · ars 2: -0.0476ns [*] · ars 3: -0.05ns [*] · ars 4: +0.202ns [*] · ars 5: +0.251ns [*] - Storey 24: · ars 0: -0.212ns [*] · ars 1: -0.234ns [*] · ars 2: -0.00701ns [*] · ars 3: -0.426ns [*] · ars 4: +0.0712ns [*] · ars 5: -0.177ns [*] - Storey 25: · ars 0: -0.0157ns [*] · ars 1: -0.0255ns [*] · ars 2: +0.0782ns [*] · ars 3: +0.117ns [*] · ars 4: +0.183ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line08_section4.png has been created · ars 5: +0.155ns [*] >========================================================================================< >>> Calibrating Line 9: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1025 (L09 S02) > Fitting for time corrections... -> Fit: offset = 3.44 slope = 0.059 (parabola = -0.00027) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: +0.287ns [*] · ars 1: +0.479ns [*] · ars 2: +0.63ns [*] · ars 3: +0.754ns [ ] · ars 4: +0.465ns [*] · ars 5: +0.502ns [*] - Storey 5: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.313ns [*] · ars 3: -0.462ns [*] · ars 4: -0.146ns [*] · ars 5: +0.292ns [*] - Storey 6: · ars 0: -1.43ns [*] · ars 1: -1.62ns [*] · ars 2: -0.129ns [*] · ars 3: +0.0142ns [*] · ars 4: +0.253ns [*] · ars 5: +0.00858ns [*] - Storey 7: · ars 0: -0.181ns [*] · ars 1: -0.22ns [*] · ars 2: -0.401ns [*] · ars 3: -0.152ns [*] · ars 4: +0.841ns [*] · ars 5: +1.14ns [*] - Storey 8: · ars 0: -0.201ns [*] · ars 1: -0.567ns [*] · ars 2: -0.408ns [*] · ars 3: +0.0291ns [*] · ars 4: -0.15ns [*] · ars 5: +0.0154ns [*] - Storey 9: · ars 0: +1.87ns [*] · ars 1: +2.28ns [ ] · ars 2: +0.132ns [*] · ars 3: -0.484ns [*] · ars 4: -0.579ns [*] · ars 5: -0.888ns [*] - Storey 10: · ars 0: +0.535ns [*] · ars 1: +0.181ns [*] · ars 2: -0.744ns [*] · ars 3: -0.745ns [*] · ars 4: +0.805ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line09_section1.png has been created · ars 5: +1.34ns [*] > Section #2: Calibrating from St11 to St16 using OB 1247 (L09 S09) > Fitting for time corrections... -> Fit: offset = -2.13 slope = 0.0583 (parabola = -0.000164) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: +0.0699ns [*] · ars 1: -0.225ns [*] · ars 2: +0.132ns [*] · ars 3: +0.147ns [*] · ars 4: +0.362ns [*] · ars 5: -0.0204ns [*] - Storey 12: · ars 0: +2.79ns [ ] · ars 1: +2.39ns [ ] · ars 2: +0.258ns [*] · ars 3: -0.0225ns [*] · ars 4: +0.0645ns [*] · ars 5: -0.059ns [*] - Storey 13: · ars 0: -0.508ns [*] · ars 1: -0.672ns [*] · ars 2: -0.431ns [*] · ars 3: -0.146ns [*] · ars 4: +0.306ns [*] · ars 5: +0.262ns [*] - Storey 14: · ars 0: +0.218ns [*] · ars 1: -0.235ns [*] · ars 2: +0.302ns [*] · ars 3: +0.73ns [*] · ars 4: +0.111ns [*] · ars 5: +0.563ns [*] - Storey 15: · ars 0: -0.481ns [*] · ars 1: -0.531ns [*] · ars 2: +4.32ns [ ] · ars 3: +4.55ns [ ] · ars 4: -0.129ns [*] · ars 5: -0.147ns [*] - Storey 16: · ars 0: -0.966ns [*] · ars 1: -0.14ns [*] · ars 2: +0.238ns [*] · ars 3: -0.201ns [*] · ars 4: -0.243ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line09_section2.png has been created · ars 5: -0.435ns [*] > Section #3: Calibrating from St17 to St22 using OB 1068 (L09 S15) > Fitting for time corrections... -> Fit: offset = -3.96 slope = 0.0561 (parabola = -0.000269) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.704ns [*] · ars 1: +0.761ns [*] · ars 2: -3.53ns [ ] · ars 3: -3.66ns [ ] · ars 4: +2.89ns [ ] · ars 5: +2.71ns [ ] - Storey 18: · ars 0: -0.0258ns [*] · ars 1: -0.0463ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.497ns [*] · ars 5: -0.534ns [*] - Storey 19: · ars 0: +0.0562ns [*] · ars 1: -0.00427ns [*] · ars 2: -0.707ns [*] · ars 3: -0.741ns [*] · ars 4: +0.939ns [*] · ars 5: +0.741ns [*] - Storey 20: · ars 0: -0.103ns [*] · ars 1: +0.939ns [*] · ars 2: -0.444ns [*] · ars 3: -0.557ns [*] · ars 4: +0.0486ns [*] · ars 5: -0.156ns [*] - Storey 21: · ars 0: -0.657ns [*] · ars 1: -0.379ns [*] · ars 2: -0.782ns [*] · ars 3: -0.485ns [*] · ars 4: -0.433ns [*] · ars 5: -0.192ns [*] - Storey 22: · ars 0: +1.03ns [*] · ars 1: +0.771ns [*] · ars 2: +0.184ns [*] · ars 3: +0.0394ns [*] · ars 4: +0.0873ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line09_section3.png has been created · ars 5: +0.162ns [*] > Section #4: Calibrating from St23 to St25 using OB 1263 (L09 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 10: > Section #0: Calibrating from St01 to St03 using OB 1232 (L08 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1242 (L10 S02) > Fitting for time corrections... -> Fit: offset = 0.651 slope = 0.0729 (parabola = 2.97e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: +4.81ns [ ] · ars 1: +4.93ns [ ] · ars 2: -0.15ns [*] · ars 3: -0.0426ns [*] · ars 4: -0.0266ns [*] · ars 5: +0.382ns [*] - Storey 5: · ars 0: +0.536ns [*] · ars 1: +0.0929ns [*] · ars 2: +6.28ns [ ] · ars 3: +7.03ns [ ] · ars 4: -1.07ns [*] · ars 5: -1.28ns [*] - Storey 6: · ars 0: +0.114ns [*] · ars 1: +0.211ns [*] · ars 2: +0.699ns [*] · ars 3: +0.19ns [*] · ars 4: +0.674ns [*] · ars 5: +1.1ns [*] - Storey 7: · ars 0: -0.918ns [*] · ars 1: -0.358ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available - Storey 8: · ars 0: -0.289ns [*] · ars 1: -0.54ns [*] · ars 2: -0.396ns [*] · ars 3: -0.372ns [*] · ars 4: +0.364ns [*] · ars 5: +0.753ns [*] - Storey 9: · ars 0: +0.322ns [*] · ars 1: +0.836ns [*] · ars 2: -0.25ns [*] · ars 3: -0.415ns [*] · ars 4: +2.61ns [ ] · ars 5: +2.52ns [ ] - Storey 10: · ars 0: -0.0699ns [*] · ars 1: -0.12ns [*] · ars 2: -0.48ns [*] · ars 3: -0.139ns [*] · ars 4: +0.187ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line10_section1.png has been created · ars 5: +0.461ns [*] > Section #2: Calibrating from St11 to St16 using OB 1277 (L10 S09) > Fitting for time corrections... -> Fit: offset = -0.162 slope = 0.0701 (parabola = 6.8e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: +0.241ns [*] · ars 1: +0.0824ns [*] · ars 2: -0.439ns [*] · ars 3: -0.557ns [*] · ars 4: +0.311ns [*] · ars 5: +0.169ns [*] - Storey 12: · ars 0: -0.156ns [*] · ars 1: -0.343ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: -0.0995ns [*] · ars 5: +0.0603ns [*] - Storey 13: · ars 0: -0.324ns [*] · ars 1: -0.311ns [*] · ars 2: -0.254ns [*] · ars 3: -0.581ns [*] · ars 4: +0.846ns [*] · ars 5: +0.925ns [*] - Storey 14: · ars 0: -0.737ns [*] · ars 1: -0.907ns [*] · ars 2: -0.0887ns [*] · ars 3: -0.179ns [*] · ars 4: +1.53ns [*] · ars 5: +1.37ns [*] - Storey 15: · ars 0: -0.48ns [*] · ars 1: -0.82ns [*] · ars 2: +0.8ns [*] · ars 3: +1.15ns [*] · ars 4: -0.0615ns [*] · ars 5: -0.0157ns [*] - Storey 16: · ars 0: -0.209ns [*] · ars 1: -0.374ns [*] · ars 2: -0.475ns [*] · ars 3: -0.0287ns [*] · ars 4: -0.204ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line10_section2.png has been created · ars 5: -0.184ns [*] > Section #3: Calibrating from St17 to St22 using OB 1249 (L10 S15) > Fitting for time corrections... -> Fit: offset = -3.14 slope = 0.106 (parabola = -0.00028) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: -0.312ns [ ] · ars 1: -0.391ns [*] · ars 2: +1.31ns [*] · ars 3: +1.14ns [*] · ars 4: +1.06ns [*] · ars 5: +0.839ns [*] - Storey 18: · ars 0: -0.173ns [*] · ars 1: -0.186ns [*] · ars 2: -1.29ns [*] · ars 3: -1.59ns [*] · ars 4: -0.801ns [*] · ars 5: -1.1ns [*] - Storey 19: · ars 0: +0.328ns [*] · ars 1: -0.095ns [*] · ars 2: -0.454ns [*] · ars 3: +0.471ns [*] · ars 4: +0.432ns [*] · ars 5: -0.0409ns [*] - Storey 20: · ars 0: -1.24ns [*] · ars 1: -0.966ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.487ns [*] · ars 5: +0.705ns [*] - Storey 21: · ars 0: +0.732ns [*] · ars 1: +0.983ns [*] · ars 2: +0.744ns [*] · ars 3: +0.548ns [*] · ars 4: -1.1ns [*] · ars 5: -1.24ns [*] - Storey 22: · ars 0: +0.515ns [*] · ars 1: +0.129ns [*] · ars 2: +0.301ns [*] · ars 3: +0.668ns [*] · ars 4: -0.135ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line10_section3.png has been created · ars 5: -0.36ns [*] > Section #4: Calibrating from St23 to St25 using OB 1224 (L10 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 11: > Section #0: Calibrating from St01 to St03 using OB 1088 (L12 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1236 (L11 S02) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #2: Calibrating from St11 to St16 using OB 1309 (L11 S09) > Fitting for time corrections... -> Fit: offset = -5.22 slope = 0.0714 (parabola = -0.000186) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.719ns [*] · ars 3: +0.96ns [*] · ars 4: -83.6ns [ ] · ars 5: -101ns [ ] - Storey 12: · ars 0: -1.99ns [*] · ars 1: -1.52ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: +0.0119ns [*] · ars 5: +0.315ns [*] - Storey 13: · ars 0: +0.991ns [*] · ars 1: +1.31ns [*] · ars 2: -0.317ns [*] · ars 3: +0.0483ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 14: · ars 0: -0.209ns [*] · ars 1: +0.167ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available - Storey 15: · ars 0: -0.291ns [*] · ars 1: -0.241ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available - Storey 16: · ars 0: -0.725ns [*] · ars 1: -0.75ns [*] · ars 2: +0.309ns [*] · ars 3: -0.477ns [*] · ars 4: +0.12ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line11_section2.png has been created · ars 5: +0.436ns [*] > Section #3: Calibrating from St17 to St22 using OB 1272 (L11 S15) > Fitting for time corrections... -> Fit: offset = -4.73 slope = 0.0741 (parabola = -0.000409) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 17: · ars 0: +0.421ns [*] · ars 1: +0.672ns [*] · ars 2: +0.224ns [*] · ars 3: +0.491ns [ ] · ars 4: +0.758ns [*] · ars 5: +0.867ns [*] - Storey 18: · ars 0: +0.0406ns [*] · ars 1: +0.0317ns [*] · ars 2: -0.4ns [*] · ars 3: -0.639ns [*] · ars 4: -0.196ns [*] · ars 5: +0.0827ns [*] - Storey 19: · ars 0: -0.478ns [*] · ars 1: -0.162ns [*] · ars 2: +0.359ns [*] · ars 3: -0.309ns [*] · ars 4: -0.704ns [*] · ars 5: -0.967ns [*] - Storey 20: · ars 0: -0.536ns [*] · ars 1: -0.663ns [*] · ars 2: +0.557ns [*] · ars 3: +0.667ns [*] · ars 4: -1.15ns [*] · ars 5: +0.116ns [*] - Storey 21: · ars 0: -0.109ns [*] · ars 1: +0.268ns [*] · ars 2: Not Available · ars 3: Not Available · ars 4: Not Available · ars 5: Not Available - Storey 22: · ars 0: -0.803ns [*] · ars 1: +0.0286ns [*] · ars 2: -0.0838ns [*] · ars 3: +0.0469ns [*] · ars 4: +0.0896ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line11_section3.png has been created · ars 5: +0.22ns [*] > Section #4: Calibrating from St23 to St25 using OB 1274 (L11 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 12: > Section #0: Calibrating from St01 to St03 using OB 1236 (L11 S02) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1088 (L12 S02) > Fitting for time corrections... -> Fit: offset = 2.43 slope = 0.0805 (parabola = -0.000108) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 4: · ars 0: +3.89ns [ ] · ars 1: +1.8ns [*] · ars 2: -0.344ns [*] · ars 3: +0.129ns [*] · ars 4: -0.176ns [*] · ars 5: +0.0117ns [*] - Storey 5: · ars 0: -0.454ns [*] · ars 1: -0.534ns [*] · ars 2: -0.148ns [*] · ars 3: -0.23ns [*] · ars 4: -0.109ns [*] · ars 5: -0.161ns [*] - Storey 6: · ars 0: -0.607ns [*] · ars 1: -0.468ns [*] · ars 2: +0.0366ns [*] · ars 3: +0.125ns [*] · ars 4: -0.0258ns [*] · ars 5: +0.469ns [*] - Storey 7: · ars 0: +0.486ns [*] · ars 1: +0.139ns [*] · ars 2: +0.0248ns [*] · ars 3: +0.363ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 8: · ars 0: -0.308ns [*] · ars 1: -0.586ns [*] · ars 2: +0.00753ns [*] · ars 3: +0.0802ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 9: · ars 0: +0.223ns [*] · ars 1: +0.414ns [*] · ars 2: -0.537ns [*] · ars 3: -0.282ns [*] · ars 4: +0.0344ns [*] · ars 5: +0.282ns [*] - Storey 10: · ars 0: Not Available · ars 1: Not Available · ars 2: -0.113ns [*] · ars 3: -0.422ns [*] · ars 4: +0.446ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line12_section1.png has been created · ars 5: +0.438ns [*] > Section #2: Calibrating from St11 to St16 using OB 1038 (L12 S09) > Fitting for time corrections... -> Fit: offset = -0.731 slope = 0.0797 (parabola = 9.97e-05) -> Time corrections: (what you have to add to the t0 to correct it) - Storey 11: · ars 0: -1.12ns [ ] · ars 1: -0.954ns [*] · ars 2: -0.591ns [*] · ars 3: -0.721ns [*] · ars 4: Not Available · ars 5: Not Available - Storey 12: · ars 0: -0.262ns [*] · ars 1: +0.00823ns [*] · ars 2: +1.47ns [*] · ars 3: +2.42ns [ ] · ars 4: +1.29ns [*] · ars 5: +1.2ns [*] - Storey 13: · ars 0: -0.448ns [*] · ars 1: -0.675ns [*] · ars 2: -0.0984ns [*] · ars 3: -0.0108ns [*] · ars 4: -3.23ns [ ] · ars 5: -2.91ns [ ] - Storey 14: · ars 0: +0.115ns [*] · ars 1: -0.0925ns [*] · ars 2: -0.72ns [*] · ars 3: -0.798ns [*] · ars 4: +0.747ns [*] · ars 5: +0.561ns [*] - Storey 15: · ars 0: Not Available · ars 1: Not Available · ars 2: +0.243ns [*] · ars 3: +0.723ns [*] · ars 4: +0.0436ns [*] · ars 5: -0.119ns [*] - Storey 16: · ars 0: -0.363ns [*] · ars 1: -0.0888ns [*] · ars 2: -0.0279ns [*] · ars 3: +0.0356ns [*] · ars 4: -0.441ns [*] Info in : png file /l/agusanlo/data/tical/intratical_10/Line12_section2.png has been created · ars 5: -0.36ns [*] > Section #3: Calibrating from St17 to St22 using OB 1041 (L12 S15) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #4: Calibrating from St23 to St25 using OB 1294 (L12 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >> Report of all ERRORs: >========================================================================================< >>> Calibrating Line 1: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1631 (L01 S02) > Section #2: Calibrating from St11 to St16 using OB 1643 (L01 S09) > Section #3: Calibrating from St17 to St22 using OB 1628 (L01 S15) > Section #4: Calibrating from St23 to St25 using OB 1621 (L01 S21) >========================================================================================< >>> Calibrating Line 2: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1095 (L02 S02) > Section #2: Calibrating from St11 to St16 using OB 1048 (L02 S09) > Section #3: Calibrating from St17 to St22 using OB 1065 (L02 S15) > Section #4: Calibrating from St23 to St25 using OB 1118 (L02 S21) >========================================================================================< >>> Calibrating Line 3: > Section #0: Calibrating from St01 to St03 using OB 1193 (L05 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1027 (L03 S02) > Section #2: Calibrating from St11 to St16 using OB 1157 (L03 S09) > Section #3: Calibrating from St17 to St22 using OB 1140 (L03 S15) > Section #4: Calibrating from St23 to St25 using OB 1106 (L03 S21) >========================================================================================< >>> Calibrating Line 4: > Section #0: Calibrating from St01 to St03 using OB 1092 (L06 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1091 (L04 S02) > Section #2: Calibrating from St11 to St16 using OB 1141 (L04 S09) > Section #3: Calibrating from St17 to St22 using OB 1115 (L04 S15) > Section #4: Calibrating from St23 to St25 using OB 1151 (L04 S21) >========================================================================================< >>> Calibrating Line 5: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1193 (L05 S02) > Section #2: Calibrating from St11 to St16 using OB 1159 (L05 S09) > Section #3: Calibrating from St17 to St22 using OB 1163 (L05 S15) > Section #4: Calibrating from St23 to St25 using OB 1158 (L05 S21) >========================================================================================< >>> Calibrating Line 6: > Section #0: Calibrating from St01 to St03 using OB 1091 (L04 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1092 (L06 S02) > Section #2: Calibrating from St11 to St16 using OB 1186 (L06 S09) > Section #3: Calibrating from St17 to St22 using OB 1046 (L06 S15) > Section #4: Calibrating from St23 to St25 using OB 1056 (L06 S21) >========================================================================================< >>> Calibrating Line 7: > Section #0: Calibrating from St01 to St03 using OB 1025 (L09 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1195 (L07 S02) > Section #2: Calibrating from St11 to St16 using OB 1116 (L07 S09) > Section #3: Calibrating from St17 to St22 using OB 1042 (L07 S15) > Section #4: Calibrating from St23 to St25 using OB 1177 (L07 S21) >========================================================================================< >>> Calibrating Line 8: > Section #0: Calibrating from St01 to St03 using OB 1242 (L10 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1232 (L08 S02) > Section #2: Calibrating from St11 to St16 using OB 1176 (L08 S09) > Section #3: Calibrating from St17 to St22 using OB 1138 (L08 S15) > Section #4: Calibrating from St23 to St25 using OB 1219 (L08 S21) >========================================================================================< >>> Calibrating Line 9: > Section #0: Calibrating from St01 to St03 using OB 1081 ( Laser ) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1025 (L09 S02) > Section #2: Calibrating from St11 to St16 using OB 1247 (L09 S09) > Section #3: Calibrating from St17 to St22 using OB 1068 (L09 S15) > Section #4: Calibrating from St23 to St25 using OB 1263 (L09 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 10: > Section #0: Calibrating from St01 to St03 using OB 1232 (L08 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1242 (L10 S02) > Section #2: Calibrating from St11 to St16 using OB 1277 (L10 S09) > Section #3: Calibrating from St17 to St22 using OB 1249 (L10 S15) > Section #4: Calibrating from St23 to St25 using OB 1224 (L10 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 11: > Section #0: Calibrating from St01 to St03 using OB 1088 (L12 S02) > ERROR: No data available to fit for this section. (ERROR WHILE READING TREE) > Section #1: Calibrating from St04 to St10 using OB 1236 (L11 S02) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #2: Calibrating from St11 to St16 using OB 1309 (L11 S09) > Section #3: Calibrating from St17 to St22 using OB 1272 (L11 S15) > Section #4: Calibrating from St23 to St25 using OB 1274 (L11 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) >========================================================================================< >>> Calibrating Line 12: > Section #0: Calibrating from St01 to St03 using OB 1236 (L11 S02) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #1: Calibrating from St04 to St10 using OB 1088 (L12 S02) > Section #2: Calibrating from St11 to St16 using OB 1038 (L12 S09) > Section #3: Calibrating from St17 to St22 using OB 1041 (L12 S15) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Section #4: Calibrating from St23 to St25 using OB 1294 (L12 S21) > ERROR: No data available to fit for this section. (NO RUNNUMBER AVAILABLE) > Finished! /////////////////////////////////////////////////////////////////////////////////////////////////////////// # LED Runes para la calibración intraline tras el HV tuning de Diciembre'11 (#10) [started the 12/12/2011 after run 61522] # @runes = ("62222" ,"62221" ,"62220" ,"62219" ,"62218" ,"62217" ,"62224" ,"62213" ,"62211" ,"62210" ,"62209" ,"62208" ,"62207" ,"62206" ,"62205" ,"62204" ,"62203" ,"62202" ,"62201" ,"62200" ,"62199" ,"62198" ,"62216" ,"62195" ); # @date = ( 120116 ); # $runcal = "2011:V4.0";